Trade quote
Custom pricing available
Tell us what you need and we'll come back with a quote.
Custom trade quote
Share your quantity and project details for a tailored quote.
DTA Flat Out Levelling System Tile Clips 1.5mm provide mechanical tension for large format porcelain and stone installations on floor and wall substrates. Constructed from high-strength polymer, these clips maintain consistent 1.5mm grout joint spacing and lock tiles into a fixed plane to prevent slumping or shifting during the adhesive curing cycle.
These ISO 9001 certified clips accommodate tile thicknesses between 2mm and 12mm and are designed for clean removal when kicked parallel to the grout line.
Frequently Asked Questions About DTA Flat Out Levelling System Tile Clips 1.5mm
Q: How do I install DTA Flat Out Levelling System Tile Clips 1.5mm?
A: Slide the base of the 1.5mm clip under the tile edge after adhesive is applied. Place the adjacent tile, insert a wedge into the clip, and tighten using levelling pliers for consistent pressure and alignment.
Q: Can I use these clips with large format tiles?
A: Yes. These clips are ideal for large format tiles, helping to maintain even spacing and eliminate lippage across wider surfaces where tile warping is more likely.
Q: Are DTA Flat Out Tile Clips 1.5mm reusable?
A: The clips are single-use and should be removed after the adhesive has cured. However, the accompanying wedges are reusable, offering cost-efficiency over multiple projects.
Q: What do I do if a clip doesn’t snap off cleanly?
A: Ensure you're removing clips by kicking or tapping parallel to the grout line. If part remains, gently tap with a rubber mallet or use pliers to twist off any excess.
Q: What tiles are compatible with the 1.5mm Flat Out clips?
A: These clips are compatible with ceramic, porcelain, and natural stone tiles ranging from 2mm to 12mm in thickness, offering great versatility across indoor and outdoor applications.
Use DTA Flat Out Levelling System Tile Clips 1.5mm for:
- Bathroom wall tiling with tight grout lines
- Kitchen splashbacks requiring clean alignment
- Large format floor tiles to prevent lippage
- Outdoor patio tiling with variable substrates
Why Use DTA Flat Out Levelling System Tile Clips 1.5mm:
- Prevents lippage and tile shifting during curing
- Ensures uniform 1.5mm grout joints for a clean finish
- Accelerates tile installation and reduces callbacks
- Ideal for both wall and floor applications in professional tiling jobs
How to apply DTA Flat Out Levelling System Tile Clips 1.5mm:
- Apply tile adhesive as per the tile manufacturer’s recommendations
- Insert the base of the 1.5mm clip beneath the tile at the edge
- Place the adjacent tile and ensure alignment
- Insert a wedge into the clip and use pliers to apply pressure
- Allow adhesive to fully cure (check adhesive cure times)
- Remove clips by kicking or tapping parallel to grout lines
DTA Flat Out Levelling System Tile Clips 1.5mm limitations:
- Not reusable – clips must be replaced for each install
- Not suitable for tile thicknesses under 2mm or over 12mm
- May crack very thin or delicate tiles if overtightened
Safety precautions when using DTA Flat Out Levelling System Tile Clips 1.5mm:
- Personal Protective Equipment: Wear gloves and eye protection when using levelling pliers
- Ventilation: Ensure adequate ventilation when working with tile adhesives
- Handling: Avoid excessive force during clip tightening to prevent tile damage
- Keep out of reach of children and store clips in a sealed container when not in use
DTA Flat Out Levelling System Tile Clips 1.5mm can be used on the following substrates:
- Concrete slabs – Ensure flatness and structural integrity
- Fibre cement sheeting – Common for bathroom and wet area walls
- Existing tiled surfaces – When correctly primed and bonded
- Render or screed – Allow to fully cure before tiling
- Choosing a selection results in a full page refresh.