For bonding melamine faced board and laminates in cabinet making and furniture construction, Everbond Melamine PVA Adhesive provides the high-solids adhesion required to join non-porous melamine surfaces to timber substrates without failing.
Everbond Melamine PVA Adhesive is a high-solids PVA/EVA-based adhesive that applies white and dries clear. It is formulated to bond difficult, non-porous melamine faces and laminates to wood-based materials. The formulation requires an exact mechanical fit between the mating surfaces; gaps between substrates will extend drying times and significantly reduce the final strength of the bond.
Surfaces must be clean and free from oil, dust, and other contaminants. Apply the adhesive evenly to one surface using a squeeze bottle or brush. The parts must be joined within the 3-minute open time and clamped or pressed until sufficient initial bond strength is achieved. For optimal bonding, timber moisture content should be between 8% and 10%, with ambient relative humidity between 60% and 70%.
Clean up wet adhesive and tools immediately with warm soapy water. Once dried, the adhesive cannot be dissolved and must be removed mechanically.
No, Everbond Melamine PVA Adhesive is a non-structural adhesive. For any application requiring structural integrity, use an adhesive specifically designed and rated for structural loads.
The recommended clamp time is 2-4 hours at 20°C and 65% relative humidity. This allows for sufficient initial strength before moving the assembly, with full bond strength achieved in 24-48 hours.
Everbond Melamine PVA Adhesive applies white and dries to a clear finish. This minimises visible glue lines on exposed joints or where a clear protective coating is applied.
Apply this adhesive at temperatures above 10°C. Optimal conditions include timber moisture content of 8-10% and relative humidity of 60-70% for best performance.
| Application | Key benefit | Primary trades |
|---|---|---|
| Cabinet construction | Achieves strong, lasting bonds on melamine faced board, a substrate often difficult for general-purpose glues. Dries clear to maintain finish quality. | Cabinet makers, Joiners |
| Furniture assembly | Reliable adhesion for internal furniture joints and components made with laminates, preventing premature delamination. | Furniture manufacturers, Shop fitters |
| Laminate bonding | Designed for specific adhesion to melamine and other difficult-to-bond surfaces, ensuring joint integrity in manufactured board products. | Shop fitters, Carpenters |
The Engineering Challenge: Melamine edges often resist bonding due to non-porous surfaces.
The System-Based Solution with Everbond: The PVA/EVA chemistry is optimised for melamine surfaces, delivering reliable wet-out and mechanical lock during pressing.
Best Practice Note: Use light sanding for laminated substrates if unsure of compatibility and maintain consistent clamping pressure throughout the panel.
The Engineering Challenge: Fast-paced assembly lines require short press times without bond failure.
The System-Based Solution with Everbond: The quick clamp and clear dry finish supports tight production cycles while delivering reliable strength on vertical joints.
Best Practice Note: Apply only as much adhesive as needed—over-application can lead to excess squeeze-out and visual imperfections on finished cabinetry.
Warning: Causes skin irritation. Causes serious eye irritation. May cause respiratory irritation.
Wear impervious gloves (e.g., nitrile rubber), safety glasses, and an apron. Wash hands thoroughly after handling.
Use in a well-ventilated area. Local exhaust ventilation may be required to maintain air concentrations below exposure standards.
Store in cool, dry, well-ventilated conditions, out of direct sunlight. Do not store below 5°C or above 40°C. Keep containers tightly closed. Shelf life is 12 months at 25°C in unopened containers. Dispose of product in accordance with local regulations; it is slightly hazardous for water.
Proper surface preparation ensures reliable bonding and maximises the performance of Everbond Melamine PVA Adhesive.
Surface prep: Surfaces must be clean, dry, and free from oil, dust, and other contaminants. Ensure mating surfaces achieve an exact fit to prevent extended drying times and compromised bond strength.
Primer: Not required. Everbond Melamine PVA Adhesive is formulated for direct adhesion to melamine and laminate surfaces.
| Property | Value |
|---|---|
| Colour | White, dries clear |
| pH (TDS) | ~4 |
| pH (SDS) | 8-10 |
| Open Time | ~3 minutes |
| Clamp Time | ~2-4 hours @20°C, 65% RH |
| Full Bond Strength | 24-48 hours |
| Coverage Rate | 150 g/m2 |
| Material Family | Polymer |
| Form | Creamy Liquid |
| Solubility in Water | Miscible with water |
| Specific Gravity | ~1.05 Kg/L |
| Boiling Point Range | >100 °C |
| Shelf Life | 12 months @ 25°C unopened |
| Minimum Application Temperature | 10°C |
| Storage Temperature Range | 5°C - 40°C |
Here are some common examples on where Everbond Melamine PVA Adhesive used by our customers.
