For prep work prior to applying adhesives, sealants, or surface primers, Adheseal IPA Cleaner removes surface contaminants to ensure a clean substrate and a reliable bond. This 100% isopropyl alcohol cleaner removes fluxes, light oils, grime, and oxides, then evaporates within seconds without leaving a residue or compromising the cure of subsequent compounds.
By stripping away surface oils and contaminants, the cleaner prepares the substrate for maximum bond strength. Because it evaporates rapidly leaving zero residue, it does not interfere with the chemical curing of PU, MS, Acrylic, or Silicone compounds. It is compatible with a wide range of common construction substrates and is safe on most plastics.
The cleaner is suitable for preparing substrates prior to applying Adheseal 50A surface prep, primers, sealants, adhesives, and membranes. Compatible substrates include:
Always work in a well-ventilated area. Dampen a clean, dry rag—preferably white to avoid dye transfer—by placing it firmly over the top of the bottle and tipping the bottle over. Do not allow the liquid to drip or pool on the floor or your hands. Wipe the material down slowly and gently, then allow it to dry.
Ensure no pools of liquid are left behind; wipe away any excess with a clean, dry, white rag. You may use a cool blow dryer to clear away any residual fibres or dust left by the rag. Once there is no evidence of residue, you can begin applying your primers, sealants, adhesives, or membranes.
Yes, Adheseal IPA Cleaner is designed for surface preparation prior to applying Adheseal 50A surface prep and our range of sealants and adhesives. It is compatible with PU, MS, Acrylic, and Silicone compounds, supporting maximum bond strength.
Adheseal IPA Cleaner is safe on most plastics, masonry, metal, timber, stone, rubber, fibreglass, porcelain, aluminium, and powder coat. Always conduct a preliminary test, especially on painted surfaces, wood finishes, or varnish, as it may cause damage.
Contaminants like oils, grime, and fluxes reduce adhesion. Adheseal IPA Cleaner evaporates completely, leaving no residue, ensuring the sealant or adhesive can achieve its documented bond strength without compromise to curing.
Adheseal IPA Cleaner is a highly flammable liquid. Use in well-ventilated areas, away from ignition sources. Wear safety shoes, chemical goggles, gloves, and an apron. Do not breathe fumes, as it may cause drowsiness or dizziness.
| Application | Key benefit | Primary trades |
|---|---|---|
| Surface preparation for Adheseal primers, sealants, and adhesives | Removes surface contaminants like oils and grime, ensuring maximum bond strength and no compromise to curing. Evaporates completely. | Tilers, Glaziers, Waterproofers, General Builders |
| General cleaning of light oils, fluxes, and oxides | Leaves no residue and is safe on most plastics, preventing surface damage or film build-up. | Electricians, Mechanics, Fabricators, Detailers |
The Engineering Challenge: Dust, oil, or paint residue compromise adhesion of waterproofing membranes and expansion joint sealants.
The System-Based Solution with Adheseal IPA Cleaner: A single IPA wipe removes contaminants and evaporates cleanly—ensuring sealant bonding is unimpeded.
Best Practice Note: Avoid pooling or reusing a dirty rag, which can reintroduce contaminants. Always work clean.
Signal Word: Danger
Wear safety shoes, gloves (nitrile rubber recommended for intermittent contact), apron, and chemical goggles. A suitable respirator is advised in enclosed spaces.
Use only in well-ventilated areas. Ensure adequate ventilation to maintain air concentrations below exposure standards. Local exhaust ventilation may be required.
Store in a cool, dry, well-ventilated place, away from direct sunlight, foodstuffs, heat, and ignition sources. Keep containers tightly closed and standing upright. Dispose of contents and containers according to local regulations.
Proper surface preparation is crucial for effective bonding and sealing. This guide outlines general preparation for common surfaces and critical testing requirements.
Acceptable substrates: Masonry, Brick, Metal, Timber, Most plastics, Stone, Painted surfaces, Rubber, Fibreglass, Porcelain, Aluminium, Powder coat.
Surface prep: Ensure surfaces are clean and free from loose material. Dampen a clean rag with Adheseal IPA Cleaner and wipe the material gently. Allow to dry completely. Use a cool blow dryer if needed to remove residual fibres.
Primer: Not required. Adheseal IPA Cleaner serves as a cleaning step prior to primer or sealant application.
Critical test: Always perform a preliminary test on an inconspicuous area of the substrate to confirm compatibility. Some materials, such as certain paints, wood finishes, or varnishes, may be damaged. Effects may not be immediately visible.
| Property | Value |
|---|---|
| Material Family | Hydrocarbon Liquid |
| Form | Clear Liquid |
| Colour | Colourless clear liquid |
| Odour | Characteristic |
| Solubility in water | Miscible with water |
| Density | 0.785 g/cm3 |
| Relative Vapour Density (air=1) | 2 |
| Vapour Pressure (20 °C) | 4.1 kPa |
| Flash Point | 12 °C |
| Autoignition Temperature | 399 °C |
| Volatile by Volume | 100% |
Here are some common examples on where Adheseal IPA Cleaner used by our customers.
