Cracked asphalt and bitumen surfaces don't just look bad; they invite water to undermine your investment. Stop the decay immediately with a fast, cold-applied solution. Gripset B26 seals cracks without fumes or hot works, letting traffic back on site in approximately 15 minutes.
Traditional hot-applied methods for sealing asphalt and bitumen cracks demand specialised equipment and significant downtime. Gripset B26 offers a cold-applied alternative, eliminating heating requirements and speeding up project completion. This solvent-free, non-toxic liquid fills cracks and horizontal joints, preventing water ingress and the subsequent degradation of the surface. It forms a durable, flexible, non-tacky seal that accommodates minor substrate movement, maintaining integrity under traffic and environmental exposure.
Before application, thoroughly clean the crack of all loose material, dirt, and organic growth using a blower or broom. Cracks must be wider than 2mm for optimal penetration and sealing. Ensure the surface is free from standing water and excessive moisture; a propane torch can be used to dry and warm the surface in cooler conditions. Gripset B26 applies easily by spray unit or spout pouring equipment. Mix the product to a fluid, homogenous consistency before use. Pour the material directly into the crack, ensuring it's slightly proud of the surface. The product penetrates deeply, and some material may draw down, requiring a second application to fully fill voids and maintain a proud finish. Tools and equipment clean easily with water while the product is still wet. Once dried, use mineral turpentine or acetone for cleanup.
Vehicular traffic can resume approximately 15 minutes after application. This rapid drying time minimises site disruption for commercial and civil projects.
GRIPSET B26 is designed for cracks in asphalt and bitumen surfaces that are greater than 2mm wide. It forms a flexible, waterproof seal, preventing water ingress and further deterioration.
The product can be applied over damp surfaces, which offers some flexibility on site. However, do not apply if rain is imminent or forecast within 24 hours of application.
No, GRIPSET B26 is not designed for expansion or movement joints. It performs best in static cracks on asphalt and bitumen where crack bridging and sealing is the primary requirement.
| Application | Key benefit | Primary trades |
|---|---|---|
| Asphalt road crack sealing (cold application) | Enables vehicular traffic in approximately 15 minutes, reducing road closure times and disruption. No heating equipment required. | Road maintenance, civil contractors |
| Waterproof seal in asphalt cracks | Forms a flexible, non-tacky film that resists water ingress, preventing further pavement deterioration. | Civil contractors, commercial property managers |
| Bitumen sealing compound for horizontal joints and gaps | Provides excellent adhesion and crack bridging properties in non-movement joints. | Asphalt layers, civil contractors |
| Sealer between old and new asphalt layers | Creates a consistent bond and waterproof barrier to improve system integrity. | Asphalt layers, road construction |
Stir with a manual paddle or drill-mounted paddle until fluid and homogeneous. Decant into a pour spout or spray unit (min. spout aperture 5 mm).
Run the spout along the crack, filling slightly proud of the surface to allow for penetration.
Use controlled passes to wet out crack walls and fill to surface level; avoid overspray on adjacent areas.
After a few minutes, re-inspect the length just filled. Top up any draw-down voids until the crack remains filled and slightly proud.
Refill only where required to ensure full-depth sealing without over-application.
Clean tools with water while wet. Once dry, remove residues with suitable solvent (e.g., mineral turpentine/acetone). Confirm non-tacky finish before reopening to traffic.
Signal Word: Warning
Wear safety shoes, overalls, gloves, chemical goggles, and a respirator if inhalation risk exists. Ensure adequate ventilation during use.
Store in a cool, dry, well-ventilated place, out of direct sunlight and away from foodstuffs. Avoid freezing conditions and off concrete floors. Keep containers closed when not in use. Shelf life is 12 months in an unopened container. Dispose of material and containers according to local regulations.
Proper surface preparation is critical for the long-term performance of GRIPSET B26, ensuring optimal adhesion and sealing properties.
Surface prep: Remove all loose material, dirt, dust, and aggregate from the crack. Clear any organic growth. Use a propane torch to remove excess moisture or dew, especially in cooler conditions, and to bring the surface temperature to recommended levels. Cracks must be greater than 2mm wide to allow for proper penetration. Ensure the crack is free from water or rising damp.
Primer: Not required. GRIPSET B26 is formulated for direct application to prepared asphalt and bitumen surfaces.
| Property | Value |
|---|---|
| Form | Liquid |
| Colour | Black |
| Specific Gravity | 1.15-1.17 |
| pH | 9.3-10.5 |
| Viscosity | 10000 - 12000 cPs |
| Solid Content | 60% |
| Shore A Hardness (ASTM D2240-97) | 50 |
| Tensile Strength (AAS1145-1989) | 0.35 MPa |
| Elongation (AS1145-1989) | 300% |
| Coverage Guide | 1 litre per 80m length at 2mm width, 5mm depth |
Here are some common examples on where Gripset B26 Asphalt Crack Filler used by our customers.
