{"title":"Permabond","description":null,"products":[{"product_id":"permabond-102-50g","title":"Permabond 102","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor high-speed production lines and fast fixturing of close-fitting components, Permabond 102 provides rapid bonding of plastics, rubber, and metals. This low-viscosity ethyl cyanoacrylate polymerises quickly when pressed into a thin film between components, utilising surface moisture to initiate the cure without mixing or heat.\u003c\/p\u003e\n\n \u003ch3\u003eFast-setting surface contact\u003c\/h3\u003e\n \u003cp\u003ePermabond 102 operates as a single-component adhesive that must be applied sparingly to a single surface. Bringing the parts together under pressure spreads the liquid to its required thin film, developing handling strength on plastics like PVC and ABS in 7 to 10 seconds, and on Buna N Rubber in 5 to 10 seconds. On non-porous rigid substrates, the cured adhesive achieves high shear strength, causing substrate failure on ABS, PVC, and polycarbonate rather than bond failure.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e0.15 mm maximum gap fill:\u003c\/strong\u003e Formulated for tight-fitting parts where surfaces make direct contact.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e5 to 15-second fixture time:\u003c\/strong\u003e Achieves initial handling strength (0.3 N\/mm² shear strength) in 5–10 seconds on Buna N Rubber, 7–10 seconds on PVC and ABS, and 10–15 seconds on steel and phenolic.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e19 to 23 N\/mm² shear strength (ISO4587):\u003c\/strong\u003e Delivers high-strength structural bonds on steel surfaces.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e24-hour full strength:\u003c\/strong\u003e Requires a full day to reach maximum cure before joint exposure to full operational loads.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e-55°C to 85°C temperature range:\u003c\/strong\u003e Withstands typical cold and warm service conditions, retaining approximately 40% strength at 100°C, and brief exposures to higher temperatures during paint baking or wave soldering.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cp\u003eSuitable for bonding close-fitting industrial plastics, rubbers, and metals. Specific compatible substrates include:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003eMetals: Steel, aluminium, and zinc.\u003c\/li\u003e\n \u003cli\u003ePlastics: PVC, ABS, polycarbonate, and phenolic.\u003c\/li\u003e\n \u003cli\u003eRubbers: Buna N Rubber and other common elastomers.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cp\u003eDo not use Permabond 102 in contact with strong oxidising materials or polar solvents, though the cured joint will withstand a brief solvent wash. Acidic surfaces or gaps larger than 0.15 mm will reduce the cure speed. Avoid bonding difficult plastics such as polypropylene, polyethylene, PTFE, or silicone without pre-treating the surfaces with Permabond Polyolefin Primer (POP).\u003c\/p\u003e\n\n \u003ch3\u003eHow to apply\u003c\/h3\u003e\n \u003cp\u003eSurfaces must be clean, dry, and free of grease before application. Clean and degrease surfaces using \u003ca href=\"\/products\/acetone\"\u003eacetone\u003c\/a\u003e or isopropanol. For aluminium, copper, and copper alloys, lightly abrade the surface with emery cloth to remove the oxide layer before bonding.\u003c\/p\u003e\n \u003cp\u003eApply the adhesive sparingly to one surface and assemble the parts quickly to ensure correct alignment. Apply sufficient pressure to spread the adhesive into a thin film. Do not disturb or re-align the joint during the first few seconds of assembly. Excess uncured adhesive can be cleaned using Permabond CA solvent, nitromethane, or acetone.\u003c\/p\u003e\n \u003cp\u003eStore the container between 2°C and 7°C. To prevent moisture condensation inside the bottle—which cures the adhesive and reduces shelf life—always allow the cold bottle to reach room temperature before opening.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Permabond","offers":[{"title":"Single","offer_id":45489908842688,"sku":"100300009","price":42.56,"currency_code":"AUD","in_stock":true},{"title":"Box of 10","offer_id":46747819475136,"sku":"100300009-PACK10","price":383.04,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/permabond-102-50g_01ed28a7-337f-428a-a21c-0835b21fe8c9.jpg?v=1791770030"},{"product_id":"permabond-240-instant-adhesive","title":"Permabond 240","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor high-speed production lines assembling plastics, rubber, or metals, Permabond 240 is a high-viscosity cyanoacrylate that fills gaps up to 0.4 mm and prevents rapid absorption on porous substrates. It polymerises quickly when pressed into a thin film between parts, utilising surface moisture to develop handling strength in 15 to 20 seconds without mixing or heat curing.\u003c\/p\u003e\n\n \u003ch3\u003eWhat it does\u003c\/h3\u003e\n \u003cp\u003ePermabond 240 is a 100% reactive, solvent-free ethyl cyanoacrylate. Its high viscosity (1,200 to 2,500 mPa.s) prevents the adhesive from running off components or soaking immediately into porous materials, ensuring enough adhesive remains in the joint to bridge gaps. The single-part formula polymerises when compressed, achieving high shear strength on metals like steel, aluminium, and zinc, as well as plastics including ABS and PVC. For existing military designs, the formulation is approved to MIL-A-46050C Type II Class 3.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e0.4 mm maximum gap fill:\u003c\/strong\u003e High-viscosity formula allows reliable bonding across larger tolerances in metal and plastic assemblies.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e15 to 20 seconds fixture time:\u003c\/strong\u003e Rapid initial strength development on steel, Buna N rubber, and phenolic substrates to maintain high-speed production flow.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e21 to 25 N\/mm² shear strength (Steel):\u003c\/strong\u003e High ultimate joint strength on steel surfaces, with substrate failure occurring on ABS (\u0026gt;8 N\/mm²) and PVC (\u0026gt;11 N\/mm²).\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e-55°C to 85°C temperature limits:\u003c\/strong\u003e Maintains standard performance across this thermal range, and can withstand brief exposure to higher temperatures for paint baking and wave soldering if the joint is not under stress.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e24-hour full cure:\u003c\/strong\u003e Complete polymerisation time required to reach final physical properties and chemical resistance.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cp\u003eThis adhesive is formulated for bonding porous substrates, rubber, plastics, and metals. Compatible substrates include:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003eMetals: Steel, Aluminium, and Zinc.\u003c\/li\u003e\n \u003cli\u003ePlastics and Synthetics: ABS, PVC, Polycarbonate (PC), Phenolic, and Buna N Rubber.\u003c\/li\u003e\n \u003cli\u003eWith primer: Polypropylene, polyethylene, PTFE, and silicone can be bonded if primed first with Permabond Polyolefin Primer (POP).\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eInstallation\u003c\/h3\u003e\n \u003cp\u003eTo prevent premature failure and ensure rapid polymerisation, follow these application steps:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eSurface preparation:\u003c\/strong\u003e Surfaces must be clean, dry, and free of grease. Degrease surfaces using \u003ca href=\"\/products\/acetone\"\u003eacetone\u003c\/a\u003e or isopropanol. For aluminium, copper, and copper alloys, lightly abrade the surface with emery cloth to remove the oxide layer before bonding.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eApplication:\u003c\/strong\u003e Apply the adhesive sparingly to one surface. Bring the components together quickly, ensuring correct alignment. Apply sufficient pressure to spread the adhesive into a thin film.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eCure assistance:\u003c\/strong\u003e Larger gaps or acidic surfaces will reduce cure speed. This can be overcome by applying Permabond C Surface Activator (CSA) or Permabond QFS 16. For difficult or porous surfaces, using a Permabond activator is recommended.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eClean-up:\u003c\/strong\u003e Uncured surplus adhesive can be removed using Permabond CA solvent, nitromethane, or acetone.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eNot recommended for use in contact with strong oxidising materials or polar solvents, though it will withstand a brief solvent wash without bond degradation.\u003c\/li\u003e\n \u003cli\u003eCure speeds will slow down in larger gaps, at lower humidity, or on acidic surfaces unless an activator is used.\u003c\/li\u003e\n \u003cli\u003eMust be stored between 2°C and 7°C. Always allow the bottle to reach room temperature before opening to prevent condensation from forming inside the container, which reduces shelf life.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Permabond","offers":[{"title":"Single","offer_id":45489886200000,"sku":"100300010","price":41.48,"currency_code":"AUD","in_stock":true},{"title":"Box of 10","offer_id":46747868397760,"sku":"100300010-PACK10","price":373.32,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/permabond-240-instant-adhesive_319d8210-1c61-4096-8c5c-0a05e3793906.jpg?v=1791770038"}],"url":"https:\/\/adheseal.com.au\/collections\/permabond.oembed","provider":"Adheseal","version":"1.0","type":"link"}