{"title":"Machinery Adhesives \u0026 Grouts","description":"\u003cp\u003eFast-fix cyanoacrylates for production lines, plus epoxy adhesive and pourable grout for ceramic wear tiles, crusher liners, and heavy machinery. Exact ratios and cure control give these products their strength.\u003c\/p\u003e","products":[{"product_id":"megapoxy-84","title":"Megapoxy 84","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor high-wear industrial environments where high alumina ceramic tile linings must be fixed to steel or concrete under elevated temperatures, Megapoxy 84 provides the high-strength, heat-tolerant bond required to prevent lining failure. It is also formulated for the extreme mechanical demands of locking the inner and outer eccentric bushings in Symons Cone Crushers and other heavy crushing machinery.\u003c\/p\u003e\n\n \u003ch3\u003eHigh-temperature thermal and mechanical performance\u003c\/h3\u003e\n \u003cp\u003eMegapoxy 84 is a two-component epoxy paste adhesive that cures to a pale blue finish. It maintains its structural bond up to a maximum continuous operating temperature of 120°C. With a compressive strength of 120 MPa, it withstands the constant heavy impact and high load paths found in industrial crushing machinery and bulk material handling chutes. The thixotropic gel consistency of Part A prevents slumping during application, ensuring a full, even bed thickness when spreading over vertical or overhead surfaces before tiles are pressed into place.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e120 MPa compressive strength:\u003c\/strong\u003e High compressive capacity to withstand heavy crushing loads and continuous impact.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e120°C maximum operating temperature:\u003c\/strong\u003e Retains structural adhesion under high-heat service conditions.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e1.25 litres per m² coverage rate:\u003c\/strong\u003e Standard application rate for spreading on steel or concrete substrates with a notched trowel.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e30-minute work time (at 25°C):\u003c\/strong\u003e Practical open window to mix, apply, and align heavy ceramic tiles before the paste begins to set.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e72-hour full service cure:\u003c\/strong\u003e The required curing period before the tiled installation can be exposed to full mechanical loads and continuous temperatures up to 120°C.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not expose the application to elevated temperatures during the initial 48-hour cure period. The product is slightly brittle in the first 48 hours and requires this window to develop its full toughness.\u003c\/li\u003e\n \u003cli\u003eDo not apply Megapoxy 84 if the substrate or ambient temperature is below the 10°C minimum application limit.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eSurface preparation\u003c\/h3\u003e\n \u003cp\u003eTo ensure a permanent, high-strength bond, substrates must be prepared to the following standards before mixing:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eSteel:\u003c\/strong\u003e Must be cleaned to a \"white metal\" finish by grinding or grit blasting.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eConcrete:\u003c\/strong\u003e Must be scabbled back or grit blasted to expose firmly held aggregate.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eTiles:\u003c\/strong\u003e High alumina ceramic tile surfaces must be clean and free of grease and contaminants.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eMixing and application\u003c\/h3\u003e\n \u003cp\u003eMegapoxy 84 is supplied in pre-measured 2.5-litre kits (4 parts Part A to 1 part Part B). To prevent measuring errors, the entire kit should be mixed at one time. Slowly pour the liquid Part B into the thixotropic Part A container to prevent splashing. Mix thoroughly for a minimum of 3 minutes using a putty knife or spatula, scraping both the sides and the bottom of the container to ensure a uniform pale blue appearance.\u003c\/p\u003e\n \u003cp\u003eApply the mixed adhesive to the prepared steel or concrete at approximately 1.25 litres per m² using a notched trowel. Press the high alumina ceramic tiles firmly into the wet adhesive bed to achieve complete, even contact across the tile surface. Uncured adhesive can be cleaned from tools and surfaces using \u003ca href=\"\/products\/megapoxy-thinners\"\u003eMegapoxy Thinners\u003c\/a\u003e and warm soapy water.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Megapoxy","offers":[{"title":"Default Title","offer_id":43822340735168,"sku":"MP84\/2.5","price":177.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/products\/megapoxy-84-epoxy-adhesive-ceramic-tile-steel-adheseal.png?v=1763706687"},{"product_id":"permabond-102-50g","title":"Permabond 102","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor high-speed production lines and fast fixturing of close-fitting components, Permabond 102 provides rapid bonding of plastics, rubber, and metals. This low-viscosity ethyl cyanoacrylate polymerises quickly when pressed into a thin film between components, utilising surface moisture to initiate the cure without mixing or heat.\u003c\/p\u003e\n\n \u003ch3\u003eFast-setting surface contact\u003c\/h3\u003e\n \u003cp\u003ePermabond 102 operates as a single-component adhesive that must be applied sparingly to a single surface. Bringing the parts together under pressure spreads the liquid to its required thin film, developing handling strength on plastics like PVC and ABS in 7 to 10 seconds, and on Buna N Rubber in 5 to 10 seconds. On non-porous rigid substrates, the cured adhesive achieves high shear strength, causing substrate failure on ABS, PVC, and polycarbonate rather than bond failure.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e0.15 mm maximum gap fill:\u003c\/strong\u003e Formulated for tight-fitting parts where surfaces make direct contact.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e5 to 15-second fixture time:\u003c\/strong\u003e Achieves initial handling strength (0.3 N\/mm² shear strength) in 5–10 seconds on Buna N Rubber, 7–10 seconds on PVC and ABS, and 10–15 seconds on steel and phenolic.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e19 to 23 N\/mm² shear strength (ISO4587):\u003c\/strong\u003e Delivers high-strength structural bonds on steel surfaces.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e24-hour full strength:\u003c\/strong\u003e Requires a full day to reach maximum cure before joint exposure to full operational loads.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e-55°C to 85°C temperature range:\u003c\/strong\u003e Withstands typical cold and warm service conditions, retaining approximately 40% strength at 100°C, and brief exposures to higher temperatures during paint baking or wave soldering.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cp\u003eSuitable for bonding close-fitting industrial plastics, rubbers, and metals. Specific compatible substrates include:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003eMetals: Steel, aluminium, and zinc.\u003c\/li\u003e\n \u003cli\u003ePlastics: PVC, ABS, polycarbonate, and phenolic.\u003c\/li\u003e\n \u003cli\u003eRubbers: Buna N Rubber and other common elastomers.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cp\u003eDo not use Permabond 102 in contact with strong oxidising materials or polar solvents, though the cured joint will withstand a brief solvent wash. Acidic surfaces or gaps larger than 0.15 mm will reduce the cure speed. Avoid bonding difficult plastics such as polypropylene, polyethylene, PTFE, or silicone without pre-treating the surfaces with Permabond Polyolefin Primer (POP).\u003c\/p\u003e\n\n \u003ch3\u003eHow to apply\u003c\/h3\u003e\n \u003cp\u003eSurfaces must be clean, dry, and free of grease before application. Clean and degrease surfaces using \u003ca href=\"\/products\/acetone\"\u003eacetone\u003c\/a\u003e or isopropanol. For aluminium, copper, and copper alloys, lightly abrade the surface with emery cloth to remove the oxide layer before bonding.\u003c\/p\u003e\n \u003cp\u003eApply the adhesive sparingly to one surface and assemble the parts quickly to ensure correct alignment. Apply sufficient pressure to spread the adhesive into a thin film. Do not disturb or re-align the joint during the first few seconds of assembly. Excess uncured adhesive can be cleaned using Permabond CA solvent, nitromethane, or acetone.\u003c\/p\u003e\n \u003cp\u003eStore the container between 2°C and 7°C. To prevent moisture condensation inside the bottle—which cures the adhesive and reduces shelf life—always allow the cold bottle to reach room temperature before opening.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Permabond","offers":[{"title":"Single Buy","offer_id":45489908842688,"sku":"CYNC2\/50","price":42.46,"currency_code":"AUD","in_stock":true},{"title":"Box Buy (10)","offer_id":46747819475136,"sku":"CYNC2\/50\/BOX","price":382.1,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/permabond-102-cyanoacrylate-adhesive-tight-gaps-adheseal.jpg?v=1763710504"},{"product_id":"permabond-240-instant-adhesive","title":"Permabond 240","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor high-speed production lines assembling plastics, rubber, or metals, Permabond 240 is a high-viscosity cyanoacrylate that fills gaps up to 0.4 mm and prevents rapid absorption on porous substrates. It polymerises quickly when pressed into a thin film between parts, utilising surface moisture to develop handling strength in 15 to 20 seconds without mixing or heat curing.\u003c\/p\u003e\n\n \u003ch3\u003eWhat it does\u003c\/h3\u003e\n \u003cp\u003ePermabond 240 is a 100% reactive, solvent-free ethyl cyanoacrylate. Its high viscosity (1,200 to 2,500 mPa.s) prevents the adhesive from running off components or soaking immediately into porous materials, ensuring enough adhesive remains in the joint to bridge gaps. The single-part formula polymerises when compressed, achieving high shear strength on metals like steel, aluminium, and zinc, as well as plastics including ABS and PVC. For existing military designs, the formulation is approved to MIL-A-46050C Type II Class 3.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e0.4 mm maximum gap fill:\u003c\/strong\u003e High-viscosity formula allows reliable bonding across larger tolerances in metal and plastic assemblies.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e15 to 20 seconds fixture time:\u003c\/strong\u003e Rapid initial strength development on steel, Buna N rubber, and phenolic substrates to maintain high-speed production flow.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e21 to 25 N\/mm² shear strength (Steel):\u003c\/strong\u003e High ultimate joint strength on steel surfaces, with substrate failure occurring on ABS (\u0026gt;8 N\/mm²) and PVC (\u0026gt;11 N\/mm²).\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e-55°C to 85°C temperature limits:\u003c\/strong\u003e Maintains standard performance across this thermal range, and can withstand brief exposure to higher temperatures for paint baking and wave soldering if the joint is not under stress.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e24-hour full cure:\u003c\/strong\u003e Complete polymerisation time required to reach final physical properties and chemical resistance.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cp\u003eThis adhesive is formulated for bonding porous substrates, rubber, plastics, and metals. Compatible substrates include:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003eMetals: Steel, Aluminium, and Zinc.\u003c\/li\u003e\n \u003cli\u003ePlastics and Synthetics: ABS, PVC, Polycarbonate (PC), Phenolic, and Buna N Rubber.\u003c\/li\u003e\n \u003cli\u003eWith primer: Polypropylene, polyethylene, PTFE, and silicone can be bonded if primed first with Permabond Polyolefin Primer (POP).\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eInstallation\u003c\/h3\u003e\n \u003cp\u003eTo prevent premature failure and ensure rapid polymerisation, follow these application steps:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eSurface preparation:\u003c\/strong\u003e Surfaces must be clean, dry, and free of grease. Degrease surfaces using \u003ca href=\"\/products\/acetone\"\u003eacetone\u003c\/a\u003e or isopropanol. For aluminium, copper, and copper alloys, lightly abrade the surface with emery cloth to remove the oxide layer before bonding.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eApplication:\u003c\/strong\u003e Apply the adhesive sparingly to one surface. Bring the components together quickly, ensuring correct alignment. Apply sufficient pressure to spread the adhesive into a thin film.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eCure assistance:\u003c\/strong\u003e Larger gaps or acidic surfaces will reduce cure speed. This can be overcome by applying Permabond C Surface Activator (CSA) or Permabond QFS 16. For difficult or porous surfaces, using a Permabond activator is recommended.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eClean-up:\u003c\/strong\u003e Uncured surplus adhesive can be removed using Permabond CA solvent, nitromethane, or acetone.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eNot recommended for use in contact with strong oxidising materials or polar solvents, though it will withstand a brief solvent wash without bond degradation.\u003c\/li\u003e\n \u003cli\u003eCure speeds will slow down in larger gaps, at lower humidity, or on acidic surfaces unless an activator is used.\u003c\/li\u003e\n \u003cli\u003eMust be stored between 2°C and 7°C. Always allow the bottle to reach room temperature before opening to prevent condensation from forming inside the container, which reduces shelf life.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Permabond","offers":[{"title":"Single Buy","offer_id":45489886200000,"sku":"CYNC4\/50","price":42.46,"currency_code":"AUD","in_stock":true},{"title":"Box Buy (10)","offer_id":46747868397760,"sku":"CYNC4\/50\/BOX","price":382.1,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/permabond-240-high-viscosity-cyanoacrylate-adheseal.jpg?v=1763710504"},{"product_id":"megapoxy-hicb","title":"Megapoxy HICB","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor backing metal liner plates and filling gaps between liners and support structures in cone crushers, gyratory crushers, and grinding mills, Megapoxy HICB is a two-component, 100% solids, pourable epoxy grout. It provides the high impact resistance and compressive strength needed to withstand heavy machinery loads on concrete and metal substrates without cracking or losing adhesion.\u003c\/p\u003e\n\n \u003ch3\u003eWhat it does\u003c\/h3\u003e\n \u003cp\u003eMegapoxy HICB cures to form a high-strength backing and reinforcement layer that absorbs extreme mechanical shock in mining and quarry machinery. This pourable, low-VOC epoxy flows into tight clearances between liner plates and support frames, securing locking bearings, chocking machinery, and grouting rail tracks. The formulation is available in both Standard and Accelerated versions, allowing installers to select the required cure speed and working window for the ambient temperature of the site.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e112 MPa compressive strength:\u003c\/strong\u003e Ultimate compressive strength (ASTM C579) ensures the cured grout carries heavy cyclic crushing forces without crushing or deforming.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e20 MPa tensile bond strength:\u003c\/strong\u003e High-strength adhesion (ASTM D897) secures metal-to-metal and metal-to-concrete contact points under severe vibration.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e50 mm maximum casting thickness:\u003c\/strong\u003e Defines the maximum depth allowed per single pour to control heat generation during cure and prevent thermal cracking.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e30-minute work time (Standard) \/ 10-minute (Accelerated):\u003c\/strong\u003e The application window at 25°C to pour and place the grout before the cure reaction begins.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e24-hour cure at 25°C (Standard) \/ 6-hour (Accelerated):\u003c\/strong\u003e Minimum curing periods required before returning crushers and heavy machinery to active service.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eCone crushers and primary gyratory crushers\u003c\/li\u003e\n \u003cli\u003eGrinding mills, rotating mills, and pulverisers\u003c\/li\u003e\n \u003cli\u003eLocking bearings and machinery chocking\u003c\/li\u003e\n \u003cli\u003eSetting anchor bolts and rail track grouting\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eInstallation and mixing\u003c\/h3\u003e\n \u003cp\u003eSuccessful application requires thorough preparation and strict mixing sequences to prevent curing failures:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eSurface preparation:\u003c\/strong\u003e Grit blast metal surfaces to AS 1627.2.2002. If grit blasting is not possible, mechanically abrade to clean, bright metal and degrease with an industrial-grade degreaser.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eCrevice sealing:\u003c\/strong\u003e Seal all crevices with a rapid-setting putty, such as \u003ca href=\"\/products\/megapoxy-pf\"\u003eMegapoxy PF\u003c\/a\u003e, to prevent the liquid backing mixture from leaking out during the pour.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eMixing process:\u003c\/strong\u003e Stir Part A to eliminate any settling. Add Part B slowly while mixing with a low-speed electric mixer for 2 minutes, scraping the base of the pail. Scrape the sides of the pail with a straight edge (do not use the mixer head) and mix for an additional minute until the blue-green colour is uniform.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eApplication:\u003c\/strong\u003e Pour immediately after mixing. If ambient temperatures are high, store the kits in a cool place prior to mixing to prevent a severely shortened working life.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not exceed the maximum casting thickness of 50 mm per pour.\u003c\/li\u003e\n \u003cli\u003eDo not apply if ambient temperatures are below the minimum application temperature of 10°C.\u003c\/li\u003e\n \u003cli\u003eDo not rely on wire brushing for metal surface preparation, as it is not entirely satisfactory and yields minimal adhesion only.\u003c\/li\u003e\n \u003cli\u003eInaccuracies in the mix ratio or incomplete mixing of Part A and Part B will lower physical properties, prevent satisfactory curing, and cause discolouration on ageing.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Megapoxy","offers":[{"title":"10kg","offer_id":45523863699648,"sku":"MPHICB\/10","price":148.06,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/megapoxy-hicb-high-impact-crusher-liner-backing-adheseal.png?v=1763711510"}],"url":"https:\/\/adheseal.com.au\/collections\/manufacturing-rapid-assembly-machinery.oembed","provider":"Adheseal","version":"1.0","type":"link"}