{"title":"Concrete \u0026 Civil Products","description":null,"products":[{"product_id":"everbond-plastabond","title":"Everbond Plastabond PVA","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eFor high-strength mortars, floor screeds, renders, and slurries requiring improved adhesion and durability, Everbond Plastabond PVA acts as a dual-purpose bonding agent and plasticising additive. This polyvinyl acetate resin water dispersion modifies sand, cement, and gypsum mixes to improve chemical resistance and lower water permeability while remaining non-corrosive to steel structural elements.\u003c\/p\u003e\n\u003ch3\u003eHow it works\u003c\/h3\u003e\n\u003cp\u003eEverbond Plastabond PVA modifies the cementitious matrix to produce polymer-modified mortars and renders with increased tensile and mechanical strengths. As an additive, it improves mix elasticity to reduce shrinkage cracking and increases resistance to oil, water, abrasion, and mild chemical attack. When applied directly as a surface bonding agent, it creates a high-adhesion keyway to secure new screeds and concrete pours to existing substrates.\u003c\/p\u003e\n\u003ch3\u003eWhere to use it\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAs an additive:\u003c\/strong\u003e Modifies patching and repair mortars, renders, floor screeds, and slurries to increase bond strength and durability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAs a bonding agent:\u003c\/strong\u003e Bonds new concrete and toppings to prepared structural surfaces.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInsulation board installations:\u003c\/strong\u003e Improves the adhesion of cementitious renders when applied directly over insulation boards and lightweight panels.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eLimitations\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePolystyrene panels:\u003c\/strong\u003e Do not use Everbond Plastabond PVA for bonding to polystyrene panels. For these substrates, refer to the technical data sheet for acrylic bonding agents.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApplication temperature:\u003c\/strong\u003e Do not apply when substrate or ambient temperatures are below 5°C or above 35°C.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCuring constraint:\u003c\/strong\u003e When used as a surface bonding agent, the topping concrete must be poured while the applied film is still tacky.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eDilution and application\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAs a plasticiser admix:\u003c\/strong\u003e Dilute between 1 part Plastabond to 10 parts water, up to 1 part Plastabond to 1 part water depending on strength requirements. Mix into the concrete or mortar to achieve the desired consistency, typically requiring 7 to 10 litres of the blended liquid per bag of cement.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAs a bonding agent:\u003c\/strong\u003e Dilute 4 parts Plastabond to 1 part water. Apply to the substrate at an approximate coverage rate of 8 square metres per litre. Pour the concrete over the wet film while it remains tacky.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClean up:\u003c\/strong\u003e Wash tools and remove uncured material immediately using clean water.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Adheseal","offers":[{"title":"5L","offer_id":37551485583552,"sku":"PLASTAB\/5","price":70.46,"currency_code":"AUD","in_stock":true},{"title":"20L","offer_id":46349645250752,"sku":"PLASTAB\/20","price":262.2,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/products\/everbond-plastabond-pva-adhesive-concrete-repair-adheseal.jpg?v=1763707148"},{"product_id":"everkrete-trade-kit","title":"EverKrete Concrete Repair System Trade Kit","description":"\u003c!-- Quick Specs Section --\u003e\n\u003cdiv class=\"quick-specs\"\u003e\u003cspan class=\"spec\"\u003e\u003cstrong\u003eUse EverKrete Concrete Repair System Trade Kit for:\u003c\/strong\u003e Rapid concrete repairs, vertical \u0026amp; overhead patching, traffic-grade overlays, and slip-resistant surface finishing\u003c\/span\u003e\u003c\/div\u003e\n\u003c!-- Main Content --\u003e\n\u003cdiv class=\"product-description\"\u003e\n\u003c!-- Summary Paragraph --\u003e\n\u003cp\u003eThe EverKrete Concrete Repair System Trade Kit is a professional-grade solution for fast, high-performance concrete repairs. Powered by EverKrete 102 thermoset vinyl polymer, this system produces a durable mortar for horizontal, vertical, and overhead surfaces. With a cure time of just 45–90 minutes, it's ideal for industrial floors, commercial pathways, and civil infrastructure.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePrimer Information:\u003c\/strong\u003e Use EverKrete Primer on all clean, dry, structurally sound surfaces. Brush or roll to create a thin, tacky bond layer before applying mortar. For cooler temperatures (below 10°C), substitute with a blend of EverKrete 102 and Accelerator for consistent adhesion.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCure Time:\u003c\/strong\u003e Cures in 45–90 minutes depending on temperature and application thickness. Allows full return to traffic use within 1.5 hours—ideal for high-demand sites needing rapid turnaround.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCoverage Rate:\u003c\/strong\u003e A 4 L kit yields approximately 12 L of repair mortar, covering up to 12 m² at 1 mm thickness. Surface overlays vary from 2–4 m²\/L depending on porosity and finish type.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eApplication Temperature Range:\u003c\/strong\u003e Apply between 10°C and 35°C (50°F to 95°F). Use Accelerator for sub-10°C applications or rapid cure needs.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eChemical Properties:\u003c\/strong\u003e Based on thermoset vinyl polymer, the cured product features \u0026gt;70 MPa compressive strength, low water absorption, and Shore D 79 hardness. Excellent bond to concrete, brick, and masonry.\u003c\/p\u003e\n\u003c!-- Key Features --\u003e\n\u003ch3\u003eKey Features of EverKrete Concrete Repair System Trade Kit\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRapid cure—traffic ready in 45–90 minutes\u003c\/li\u003e\n\u003cli\u003eSupports horizontal, vertical, and overhead applications\u003c\/li\u003e\n\u003cli\u003eNon-shrink and high-strength (\u0026gt;70 MPa compressive)\u003c\/li\u003e\n\u003cli\u003eCustomisable finish from feather edge to aggressive slip resistance\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy Choose EverKrete Concrete Repair System Trade Kit:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eTrade-friendly kit includes measuring tools, primer, and instructions\u003c\/li\u003e\n\u003cli\u003ePerforms in extreme temperatures with optional accelerator\u003c\/li\u003e\n\u003cli\u003eIdeal for reactive site conditions and fast patch turnarounds\u003c\/li\u003e\n\u003cli\u003eDesigned to bond with common Australian substrates\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhen to Choose EverKrete Concrete Repair System Trade Kit versus Alternatives:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eChoose EverKrete over epoxy fillers when:\u003c\/strong\u003e You need faster return to service and surface flexibility\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConsider other options when:\u003c\/strong\u003e Application temperatures fall below -18°C and heating is not feasible\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTrade-Specific Applications for EverKrete Concrete Repair System Trade Kit:\u003c\/h3\u003e\n\u003cdiv class=\"trade-section\"\u003e\n\u003ch3\u003eFor Builders and Carpenters:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eFeather-edge smoothing and slab corner patching\u003c\/li\u003e\n\u003cli\u003eCompatible with cured concrete and structural screeds\u003c\/li\u003e\n\u003cli\u003eFast turnaround ideal for critical path milestones\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"trade-section\"\u003e\n\u003ch3\u003eFor Waterproofers and Maintenance Technicians:\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIdeal under membranes or coatings for seamless subgrade repairs\u003c\/li\u003e\n\u003cli\u003eLow water absorption for long-term durability\u003c\/li\u003e\n\u003cli\u003ePerforms reliably in humid and coastal regions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003ch3\u003eApplication Information\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRequired Tools:\u003c\/strong\u003e Mixing paddle, measuring cups, stainless steel trowel, roller, acetone, cloth tape\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTrade-Specific Tips:\u003c\/strong\u003e Use acetone-wiped trowels for smooth finishes; heat surfaces in cool weather to speed primer cure\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCommon Issues and Solutions:\u003c\/strong\u003e Use Accelerator below 10°C; always use kiln-dried sand to avoid moisture-related failure\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eStorage and Shelf Life\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eStorage Requirements:\u003c\/strong\u003e Store in a cool, dry place between 10°C and 35°C\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShelf Life Information:\u003c\/strong\u003e 12 months from production if unopened and properly stored\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTemperature Considerations:\u003c\/strong\u003e Avoid exposure to freezing or excessive heat in transit or storage\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCertifications and Compliance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eASTM D638 – Tensile Properties\u003c\/li\u003e\n\u003cli\u003eASTM D790 – Flexural Strength\u003c\/li\u003e\n\u003cli\u003eASTM D2240 – Shore Hardness\u003c\/li\u003e\n\u003cli\u003eASTM D570 – Water Absorption\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003cp\u003e\u003cstrong\u003eThis product is designed for industry professionals, as it requires careful attention to instructions for proper use to ensure the best results and prevent any potential issues.\u003cbr\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWe strongly encourage users to download the EverKrete Trade Kit TDS as it contains important information on how to use and apply this product.\u003c\/strong\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThis Trade Kit Includes: \u003c\/strong\u003e\u003cbr\u003e• EverKrete 102 (4 L) \u003cbr\u003e• EverKrete Primer (500 mL) \u003cbr\u003e• EverKrete Catalyst (50 mL) \u003cbr\u003e• White Sand 0.6 mm (20 kg) \u003cbr\u003e• Comprehensive Instructions Manual\u003cbr\u003e• Mixing Pail \u003cbr\u003e• 1 L Measuring Cup \u003cbr\u003e• 30 mL Measuring Cup\u003cbr\u003eMakes approximately 12 litres.\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFor larger volumes (sold separately): \u003cbr\u003e\u003c\/strong\u003e• \u003ca href=\"https:\/\/adheseal.com.au\/products\/everkrete-102?variant=39282785059008\" rel=\"noopener\" target=\"_blank\"\u003eEverKrete 102 (20 kg, includes 225 mL catalyst)\u003c\/a\u003e\u003cbr\u003e• \u003ca rel=\"noopener\" href=\"https:\/\/adheseal.com.au\/products\/everkrete-2p-primer?variant=37551484928192\" target=\"_blank\"\u003eEverKrete Primer (2 L)\u003c\/a\u003e\u003cbr\u003e• \u003ca rel=\"noopener\" href=\"https:\/\/adheseal.com.au\/products\/everkrete-2p-primer?variant=37551484960960\" target=\"_blank\"\u003eEverKrete Primer (8 L)\u003c\/a\u003e\u003cbr\u003e• \u003ca href=\"https:\/\/adheseal.com.au\/products\/kiln-dried-sand\" rel=\"noopener\" target=\"_blank\"\u003e0.6 mm Sand (20 kg per bag, 5 bags)\u003c\/a\u003e\u003cbr\u003eMakes approximately 56.7 litres.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFor Vertical \u0026amp; Overhead applications (sold separately):\u003c\/strong\u003e\u003cbr\u003eEverKrete LVS or Fumed Silica is required.\u003cbr\u003eFor Temps below 10dg or rapid cure: \u003ca rel=\"noopener\" href=\"https:\/\/adheseal.com.au\/products\/everkrete-accelerator\" target=\"_blank\"\u003eEverKrete Accelerator\u003c\/a\u003e is required.\u003c\/p\u003e","brand":"EverKrete","offers":[{"title":"Default Title","offer_id":37551511666880,"sku":"EKTK","price":283.33,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/everkrete-concrete-repair-trade-kit-rapid-adheseal.png?v=1763708493"},{"product_id":"everkrete-accelerator","title":"EverKrete Accelerator","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor cold room installations, winter concrete repairs, or high-traffic commercial floors where you cannot afford standard cure windows, Accelerator speeds up \u003ca href=\"\/products\/everkrete-102\"\u003eEverKrete 102\u003c\/a\u003e resin to achieve a full cure in as little as 15 minutes. This single-component additive allows for successful applications down to -18°C, preventing frozen or uncured resin on cold substrates.\u003c\/p\u003e\n\n \u003ch3\u003eCure acceleration and cold-weather priming\u003c\/h3\u003e\n \u003cp\u003eAccelerator modifies the curing reaction of EverKrete 102 resin to drastically shorten return-to-service times. In low-temperature environments, standard resins slow down or stop curing entirely; adding this accelerant keeps the chemical reaction active on cold concrete, masonry, and screeds. It also serves as a low-temperature priming system when mixed with EverKrete 102 at ratios between 100:1 and 200:1, securing adhesion on substrates from +10°C down to -18°C.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e-18°C to 35°C application range:\u003c\/strong\u003e The safe service window for chemical reaction, allowing repairs in active cold storage facilities and sub-zero winter environments.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e15-minute minimum cure time:\u003c\/strong\u003e The fastest achievable full cure under optimal conditions, minimising downtime on critical traffic paths.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e100:1 to 1000:1 variable mix ratio:\u003c\/strong\u003e Highly adjustable dosage control to balance your work time against the ambient, substrate, and material temperatures on-site.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e300:1 standard starting ratio:\u003c\/strong\u003e The recommended baseline mix (such as adding 3.3 ml of Accelerator to 1 litre of catalysed EverKrete 102) for initial on-site testing.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cp\u003eThis additive is compatible with EverKrete 102 applications on the following substrates:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003eConcrete cured for a minimum of 28 days\u003c\/li\u003e\n \u003cli\u003eBurnished concrete and pre-cast concrete (once release agents are fully removed or dissipated)\u003c\/li\u003e\n \u003cli\u003e3:1 sand cement screed or C-Bed\u003c\/li\u003e\n \u003cli\u003eMasonry and render cured for at least 4 days\u003c\/li\u003e\n \u003cli\u003eBrickwork and Hebel aggregate blocks\u003c\/li\u003e\n \u003cli\u003eCeramic tiles and some plastics\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eMixing and application\u003c\/h3\u003e\n \u003cp\u003eBecause this additive rapidly shortens working time, careful measurement and preparation are required to avoid premature curing in the vessel.\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eDo not mix additives simultaneously:\u003c\/strong\u003e Never add the standard catalyst and Accelerator to the resin at the same time.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eStep 1:\u003c\/strong\u003e Thoroughly mix the standard catalyst into the EverKrete 102 resin first.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eStep 2:\u003c\/strong\u003e Measure the exact dose of Accelerator and add it to the already catalysed resin.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eStep 3:\u003c\/strong\u003e Power mix for 30 to 60 seconds to ensure even dispersion before immediate application.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eClean-up:\u003c\/strong\u003e Clean all mixing tools and wet spills immediately using \u003ca href=\"\/products\/acetone\"\u003eAcetone\u003c\/a\u003e. Once cured, the product must be removed mechanically.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not apply if ambient or substrate temperatures are below -18°C or above 35°C.\u003c\/li\u003e\n \u003cli\u003eDo not apply to damp, wet, or contaminated surfaces.\u003c\/li\u003e\n \u003cli\u003eDo not apply if rain is falling or imminent.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"EverKrete","offers":[{"title":"Default Title","offer_id":37551511699648,"sku":"EKACCEL\/225","price":37.5,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/everkrete-accelerator-15min-cure-concrete-repair-adheseal.png?v=1763708493"},{"product_id":"mapegrout-t40","title":"Mapei Mapegrout T40 Mortar","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor repairing degraded vertical or horizontal concrete surfaces, Mapegrout T40 Mortar provides a medium-strength, thixotropic system that can be applied to vertical faces and ceilings without slumping or requiring formwork. It is formulated to match the physical characteristics of medium-quality concrete, preventing differential movement cracks on pillars, beams, balconies, tunnels, and canal linings.\u003c\/p\u003e\n\n \u003ch3\u003eHow it works\u003c\/h3\u003e\n \u003cp\u003eMapegrout T40 Mortar is a cement-based, fibre-reinforced mortar that complies with EN 1504-3 as a Class R3 structural mortar. When mixed with water, its thixotropic consistency allows high-build application up to 35 mm per layer without falling away from the substrate. It features a shrinkage-compensated formula that counteracts plastic shrinkage during the initial curing phase, provided the substrate is rough and correctly reinforced.\u003c\/p\u003e\n \u003cp\u003eTo ensure the expansion properties develop correctly when curing in open-air conditions on site, the mortar can be mixed with 0.25% Mapecure SRA. This additive acts as an internal curing agent to slow water evaporation, reducing dry shrinkage by 20% to 50% and lowering the risk of surface cracking. Once cured, the mortar is waterproof and shares a similar modulus of elasticity, thermal expansion, and permeability to existing medium-grade concrete substrates.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e40 MPa compressive strength\u003c\/strong\u003e (after 28 days to EN 12190): Achieves Class R3 structural performance, with \u0026gt;8 MPa after 1 day and \u0026gt;30 MPa after 7 days to match medium-strength concrete loads.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e30 to 35 mm thickness per layer\u003c\/strong\u003e: The maximum application thickness achievable in a single pass on vertical surfaces or ceilings without using formwork.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e1-hour work time\u003c\/strong\u003e (at +20°C): The practical pot life window for manual trowel or spray application before the cement matrix begins to set.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e18.5 kg\/m² consumption rate\u003c\/strong\u003e: Practical estimation base of 18.5 kg of dry powder required per square metre for every centimetre of application thickness.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eAS\/NZS 4020:2005 compliant\u003c\/strong\u003e: Tested and verified for use in contact with drinking water, making it suitable for hydraulic structures, canals, and water management projects.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eReconstructing degraded concrete coverings over rusted reinforcing bars on balconies, beams, and pillars.\u003c\/li\u003e\n \u003cli\u003eFilling rigid concrete joints and patching surface defects, including exposed aggregate, tie-rod holes, and protruding steel.\u003c\/li\u003e\n \u003cli\u003eRepairing concrete linings in tunnels, diaphragms, canals, and hydraulic projects.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not use to repair structures subject to high compressive loads, high impact, or abrasion; use Mapegrout Thixotropic or Mapegrout T60 instead.\u003c\/li\u003e\n \u003cli\u003eDo not use when the mortar must be pumped over long distances or through large pumping heads; use Mapegrout Easy Flow.\u003c\/li\u003e\n \u003cli\u003eDo not apply to smooth concrete surfaces; the substrate must be thoroughly roughened first.\u003c\/li\u003e\n \u003cli\u003eDo not use for anchoring jobs; use Mapefill or Mapefill R.\u003c\/li\u003e\n \u003cli\u003eDo not pour or pump this product into formwork; use Mapegrout Hi-Flow.\u003c\/li\u003e\n \u003cli\u003eDo not add cement, other admixtures, or extra water once the mix has started to set.\u003c\/li\u003e\n \u003cli\u003eDo not apply at temperatures below +5°C.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eInstallation and curing requirements\u003c\/h3\u003e\n \u003cp\u003ePrepare the substrate by removing all loose or degraded concrete until a solid, rough surface is reached. Sandblast the concrete and any exposed reinforcing steel to remove rust, paint, and laitance. Treat exposed reinforcing bars with Mapefer or Mapefer 1K before applying the mortar. The concrete substrate must be saturated with water, allowing excess surface water to evaporate before application.\u003c\/p\u003e\n \u003cp\u003eFor manual trowel application, mix each 25 kg bag with 3.8 to 4.0 litres of clean water. For spray application using Turbosol or Putzmeister type equipment (excluding continuous mixers), use 3.9 to 4.1 litres of water. If a second layer is required, apply it within 4 hours (at +23°C) before the first layer has finished setting.\u003c\/p\u003e\n \u003cp\u003eTo prevent rapid water loss and subsequent plastic shrinkage cracking, the repair must be cured. Spray water onto the surface 8 to 12 hours after application and repeat every 3 to 4 hours for at least the first 48 hours. Alternatively, apply Mapecure E, Mapecure S, or Elastocolor Primer immediately after tamping. Note that Mapecure E and Mapecure S must be completely sandblasted off if a subsequent skim coat (such as Monofinish or Mapelastic) or paint is to be applied; Elastocolor Primer can be directly overcoated with Elastocolor Paint without removal.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Mapei","offers":[{"title":"Default Title","offer_id":37551511830720,"sku":"MAPEGROUTT40","price":86.31,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/mapei-mapegrout-t40-r3-vertical-concrete-repair-adheseal.png?v=1763708493"},{"product_id":"everkrete-102","title":"EverKrete 102","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eFor fast-turnaround concrete repairs, cold-weather priming, and slip-resistant protective toppings, EverKrete 102 is a flexible, micro-fibre reinforced thermoset vinyl polymer binder. Mixed with kiln-dried sand and aggregate, it forms a high-strength concrete repair mortar, or can be saturated with sand to create a hard-wearing surface overlay.\u003c\/p\u003e\n\u003ch3\u003eWhat it does\u003c\/h3\u003e\n\u003cp\u003eEverKrete 102 functions as the chemical binder in the EverKrete concrete repair system, curing rapidly to allow full traffic access within 90 minutes. The thermoset vinyl polymer chemistry provides low viscosity to easily wet out aggregate, and once cured, it does not re-emulsify in wet or outdoor environments. It also serves as a cold-weather concrete primer on cold substrates down to -18°C, ensuring adhesion where conventional primers fail to cure.\u003c\/p\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e45 to 90 minutes cure time:\u003c\/strong\u003e Allows full traffic return quickly after installation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e-18°C to +35°C application range:\u003c\/strong\u003e Wide working window, requiring \u003ca href=\"\/products\/everkrete-accelerator\"\u003eEverKrete Accelerator\u003c\/a\u003e for temperatures below 10°C.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e13-minute pot life (unfilled at 25°C):\u003c\/strong\u003e Quick working window that extends to approximately 20 minutes when mixed with 80% aggregate.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e99% solids by weight:\u003c\/strong\u003e High-build resin formulation with minimal volume loss, exhibiting 1.1% linear shrinkage unfilled and 0% shrinkage when filled.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e500 to 700 mPa.s viscosity:\u003c\/strong\u003e Low-viscosity sticky liquid that flows easily to saturate dry aggregates and penetrate concrete capillaries.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhere to use it\u003c\/h3\u003e\n\u003cp\u003eEverKrete 102 is suitable for internal and external applications on the following prepared substrates:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eConcrete cured for a minimum of 28 days\u003c\/li\u003e\n\u003cli\u003e3:1 sand cement screed or C-Bed\u003c\/li\u003e\n\u003cli\u003eMasonry and render cured for at least 4 days\u003c\/li\u003e\n\u003cli\u003ePre-cast concrete once all release agents are completely removed or dissipated\u003c\/li\u003e\n\u003cli\u003eBrickwork, Hebel, and concrete blocks\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation limits\u003c\/h3\u003e\n\u003cp\u003eTo prevent adhesion failure and ensure a correct chemical cure, the following application parameters must be maintained:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMoisture and weather:\u003c\/strong\u003e Do not apply on damp, wet, or contaminated substrates, or if rain is imminent.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSubstrate temperature limits:\u003c\/strong\u003e Surface temperature must be between 10°C and +35°C if applying without EverKrete Accelerator. With EverKrete Accelerator, the acceptable surface temperature range is -18°C to +35°C. Do not apply if the surface temperature is below -18°C or above +35°C.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCatalysation sequence:\u003c\/strong\u003e Always pre-mix EverKrete 102 to disperse any settled material, and thoroughly mix in the EverKrete Catalyst before adding any sand, aggregate, or EverKrete LVF (Low Volume Filler).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMixing ratio:\u003c\/strong\u003e Use 2 parts Catalyst to 100 parts EverKrete 102 by weight. This can be increased up to 3 parts Catalyst to 100 parts resin for a faster cure.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eChemical caution:\u003c\/strong\u003e Do not add EverKrete Catalyst and EverKrete Accelerator to the mix at the same time. Add and mix the catalyst first, then add the accelerator.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAggregates:\u003c\/strong\u003e Use only kiln-dried sand. For general repairs, use 20-40 mesh (coarse) sand; for fine feather-edging, use 40-60 mesh (fine) sand.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClean-up:\u003c\/strong\u003e Clean tools and spills with Acetone while the resin is still wet. Cured material can only be removed mechanically. Do not use coloured rags for clean-up to avoid dye bleeding into the resin.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSystem components\u003c\/h3\u003e\n\u003cp\u003eDepending on the repair requirements, EverKrete 102 is used in conjunction with:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eEverKrete Catalyst:\u003c\/strong\u003e Required powder initiator (included with the resin).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEverKrete Primer (EverKrete 2P):\u003c\/strong\u003e Substrate primer. EverKrete 102 mortar must be applied on the same day as the primer, while the primer is dry to a tacky state.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEverKrete Accelerator:\u003c\/strong\u003e Additive to speed up curing or enable application on cold substrates below 10°C.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEverKrete LVF (Low Volume Filler):\u003c\/strong\u003e For adjusting mortar consistency and achieving a greyer finish.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e","brand":"EverKrete","offers":[{"title":"4kg (Includes 90ml catalyst)","offer_id":39282785026240,"sku":"EK102\/4","price":213.97,"currency_code":"AUD","in_stock":true},{"title":"20kg (included 450ml catalyst)","offer_id":46349641744576,"sku":"EK102\/20","price":618.75,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/everkrete-102-4l-rapid-cure-concrete-repair-adheseal.png?v=1763709484"},{"product_id":"rla-penaflow-panel-grout","title":"RLA Penaflow Panel Grout","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor structural support underneath precast concrete panels, filling core holes, and underpinning concrete sections, RLA Penaflow Panel Grout provides a shrink-compensated, Class A cementitious barrier that eliminates settlement gaps. It is formulated to expand in its plastic state to ensure complete void filling, maintaining load-bearing contact across cavities and base infills without staining adjacent substrates.\u003c\/p\u003e\n\n \u003ch3\u003ePlastic state expansion\u003c\/h3\u003e\n \u003cp\u003ePenaflow Panel Grout utilizes a gaseous expansion mechanism that operates while the grout is still in a plastic state. This controlled 1% to 2% expansion begins 15 minutes after mixing and finishes within 3 hours, pre-empting the natural shrinkage and settlement common to standard cementitious mixes. The non-metallic formulation contains no iron, preventing rust staining on exposed concrete faces or panel joints. The grout can be placed at thicknesses from 20mm up to 150mm in a single application, allowing installers to pack, pour, or pump the material depending on the access limits of the joint.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e55 MPa compressive strength:\u003c\/strong\u003e Reaches high strength at 28 days (tested to AS1012.9 and AS2073) to sustain heavy structural loads under precast panels and concrete sections.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e20mm to 150mm application depth:\u003c\/strong\u003e Enables deep single-pass placement in cavities, gaps, and core holes without requiring layered lifts.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e1% to 2% plastic expansion:\u003c\/strong\u003e Volumetric expansion occurs between 15 minutes and 3 hours after mixing to counteract plastic shrinkage.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e\u0026gt;10 MPa slant shear bond strength:\u003c\/strong\u003e Achieves strong adhesion to concrete substrates at 28 days (tested via ASTM C882-1987) to resist shifting under load.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e0% bleeding:\u003c\/strong\u003e Zero-bleed formula prevents water separation, maintaining a homogeneous mix that will not weaken the upper bond line.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eGrouting underneath precast panels and structural concrete sections.\u003c\/li\u003e\n \u003cli\u003eFilling core holes created in panels by core drilling.\u003c\/li\u003e\n \u003cli\u003eFilling cavities, gaps, and base infills.\u003c\/li\u003e\n \u003cli\u003eCore filling in concrete block work.\u003c\/li\u003e\n \u003cli\u003eUnderpinning existing concrete structures.\u003c\/li\u003e\n \u003cli\u003eSecuring and filling around anchor bolts.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eDo not mix by hand:\u003c\/strong\u003e Must be mixed mechanically with a forced-action mixer, high-shear mixer, or electric drill with a spiral paddle at 500-600 rpm.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eWater ratio limits:\u003c\/strong\u003e Do not add water beyond the specified limits (maximum 4.0L per 20kg bag). Excess water causes segregation, bleeding, and reduced strength.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eNo dry application:\u003c\/strong\u003e Never apply mixed grout to a dry, porous substrate. Saturated surface preparation is required.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eDo not vibrate:\u003c\/strong\u003e Do not use mechanical vibrators to assist the flow of the grout; use a header box to maintain gravity flow.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eUnrestrained areas:\u003c\/strong\u003e Keep unrestrained grout areas to a minimum to ensure structural performance.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eTemperature boundaries:\u003c\/strong\u003e Apply only between 10°C and 30°C. Low temperatures delay setting and strength development; high temperatures accelerate setting and increase cracking risks.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003ePreparation and installation\u003c\/h3\u003e\n \u003cp\u003eAll concrete substrates must be clean, sound, and free from curing compounds, dust, oil, or grease. Prepared areas must be saturated with water for 4 hours before grouting to reduce substrate porosity. All standing water and puddles must be removed from holes and cavities before placement begins.\u003c\/p\u003e\n \u003cp\u003eWhen grouting under base plates, bleed holes or venting holes must be provided to prevent pressure build-up. Formwork must be watertight, which can be achieved by sealing the joints with foam rubber strips, polyurethane, or silicone. Construct the formwork to maintain a continuous grout head above the level of the underside of the base plate, allowing gravity flow without trapping air.\u003c\/p\u003e\n \u003cp\u003eMix the grout by adding the powder to pre-measured cold water. Mix for 3 to 5 minutes until homogeneous. Discard any mix that has stiffened or become unworkable.\u003c\/p\u003e\n\n \u003ch3\u003eConsistency and yield\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eDry Pack \/ Stiff Grout:\u003c\/strong\u003e 2.7 to 2.9 litres of water per 20kg bag. Yields approximately 10.3 litres per bag. Initial set at 1.5 hours; final set at 2.5 hours.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003ePlastic \/ Trowellable Grout:\u003c\/strong\u003e 3.0 to 3.4 litres of water per 20kg bag. Yields approximately 10.6 litres per bag. Initial set at 3 hours; final set at 4.5 hours.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eFlowable \/ Pourable Grout:\u003c\/strong\u003e 3.6 to 4.0 litres of water per 20kg bag. Yields approximately 11.0 litres per bag. Initial set at 4.5 hours; final set at 6.5 hours.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eCuring\u003c\/h3\u003e\n \u003cp\u003eCuring is critical to the final strength and performance of the grout. Upon completion of placement, cure all exposed grout surfaces immediately using plastic sheeting, wet hessian, or a wet liquid curing compound from the RLA Curecon range.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"RLA","offers":[{"title":"Default Title","offer_id":45418145710272,"sku":"GROUTAFTEKPG\/20","price":23.24,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/penaflow-panel-grout-non-shrink-precast-panels-adheseal.png?v=1763709484"},{"product_id":"rla-penapatch-panel-lw-repair-mortar","title":"RLA Penapatch Panel LW Mortar","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor patching repairs and covering metal joining plates in tilt-up or pre-cast panels, \u003ca href=\"\/products\/rla-penapatch\"\u003ePenapatch\u003c\/a\u003e Panel LW Mortar provides a lightweight, shrinkage-compensated option that eliminates the need for formwork. It is formulated to rebuild damaged concrete, masonry, steel, and rebar surfaces, achieving a four-hour fire rating to AS1530.4 when applied at a thickness of 35mm.\u003c\/p\u003e\n\n \u003ch3\u003eHigh-build repair mechanism\u003c\/h3\u003e\n \u003cp\u003ePenapatch Panel LW Mortar combines lightweight aggregates, select cements, and polymers to allow deep vertical and overhead build-ups without sagging. The polymer-modified formula is shrinkage-compensated to ensure long-term dimensional stability and prevent cracking at the bond line. It adheres directly to concrete, masonry, steel, and rebar, and can be sanded to a smooth finish compatible with conventional decorative coatings and the RLA range of protective coatings.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eFour-hour fire rating:\u003c\/strong\u003e Tested to AS1530.4 when applied at a minimum thickness of 35mm to protect steel jointing plates and structural components.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e5mm to 100mm thickness:\u003c\/strong\u003e Accommodates builds from 5mm up to 50mm on vertical surfaces, and up to 100mm on overhead soffits in a single application.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e20 MPa compressive strength:\u003c\/strong\u003e Reaches 4.0 MPa at 1 day, 18 MPa at 7 days, and 20 MPa at 28 days (tested to AS1012 and AS2073 at 20°C) for non-structural concrete restoration.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e3 to 5 hour setting window:\u003c\/strong\u003e Initial set at 3 hours with a final set at 5 hours (at 20°C) to allow efficient finishing and sanding.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e1.85 kg\/m²\/mm coverage:\u003c\/strong\u003e Highly predictable material estimation, yielding approximately 15 litres of wet mortar per 10kg bag.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eCovering metal joining plates in tilt-up or pre-cast concrete construction.\u003c\/li\u003e\n \u003cli\u003ePatching damaged concrete, pre-cast panels, or non-structural tilt-up panels.\u003c\/li\u003e\n \u003cli\u003eHigh-build vertical repairs up to 50mm and overhead soffits up to 100mm.\u003c\/li\u003e\n \u003cli\u003eGeneral non-structural concrete and masonry repairs requiring a lightweight mortar.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not use for load-bearing applications; this is a non-structural repair mortar.\u003c\/li\u003e\n \u003cli\u003eNot recommended or designed for pedestrian or vehicle traffic.\u003c\/li\u003e\n \u003cli\u003eDo not apply to new concrete substrates cured for less than 21 days.\u003c\/li\u003e\n \u003cli\u003eDo not apply in areas thinner than 5mm, except for occasional localized touch-ups.\u003c\/li\u003e\n \u003cli\u003eIf the receiving substrate moves or cracks, reflective cracking will transfer through this mortar.\u003c\/li\u003e\n \u003cli\u003eDo not let the applied mortar come into contact with water or rain for a minimum of 24 hours.\u003c\/li\u003e\n \u003cli\u003eDo not apply at temperatures below 5°C or above 35°C.\u003c\/li\u003e\n \u003cli\u003eDo not add excess water beyond the specified 3.1 to 3.6 litres per 10kg bag, as this causes sagging, extends cure times, and reduces final strength.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eApplication guide\u003c\/h3\u003e\n \u003cp\u003eClean the substrate to remove all oil, grease, paint, and laitance. Remove cracked or weakened concrete, and clean any exposed steel or rebar to a bright condition to remove corrosion. Prime cleaned steel reinforcement with RLA Zinc Primer and allow it to dry completely before applying the mortar.\u003c\/p\u003e\n \u003cp\u003ePre-soak concrete and masonry surfaces with clean water, ensuring no standing water remains. For highly porous surfaces, apply \u003ca href=\"\/products\/rla-primer-rendergrip-a\"\u003eRLA Rendergrip\u003c\/a\u003e A before pre-soaking to prevent the mortar from flash drying and losing its workability.\u003c\/p\u003e\n \u003cp\u003eTo mix, add the powder slowly into 3.1 to 3.6 litres of clean water per 10kg bag while mixing with a high-shear spiral paddle on slow to medium speed. Mix until a smooth, soft consistency is achieved. Apply by trowel or gloved hand, compacting the mortar firmly into the substrate and around reinforcement. Finish with a steel trowel without overworking the surface. In warm, windy, or exposed conditions, apply RLA Rendergrip A as a curing agent after the final trowel to prevent premature drying.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"RLA","offers":[{"title":"Default Title","offer_id":43822341259456,"sku":"MORTARAFTEKLW\/10","price":75.23,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/rla-penapatch-panel-lw-concrete-repair-adheseal.png?v=1778907099"},{"product_id":"gripset-c-plug-rapid-set-waterproof-plug","title":"Gripset C-Plug","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor active water leaks under pressure through holes, cracks, and openings in concrete and masonry, Gripset C-Plug forms an instant, non-shrink waterproof seal. This rapid-setting cementitious compound stops flowing water in underground car parks, basements, lift shafts, water tanks, and concrete pipes before curing to the mechanical strength of concrete.\u003c\/p\u003e\n\n \u003ch3\u003eHow it works\u003c\/h3\u003e\n \u003cp\u003eC-Plug uses a rapid-setting, non-shrink chemical mechanism to expand slightly and lock into concrete or masonry cavities, blocking active water pressure. Hand-mixed and applied in small, individual batches, it goes from a paste to an initial set in under 60 seconds, allowing installers to hold back water flow manually until the seal is established. It does not contain additives that promote the corrosion of steel reinforcement, making it compatible with structural concrete repairs, subterranean joint filling, and the rapid anchoring of bolts, fixtures, and pipes.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eInitial set of under 1 minute:\u003c\/strong\u003e Provides the fast reaction window required to hold back active, pressurised water leaks by hand before the compound hardens.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e8MPa compressive strength at 30 minutes:\u003c\/strong\u003e Reaches structural load-bearing capacity rapidly, preventing the plug from washing out under early hydrostatic pressure.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e35MPa compressive strength at 28 days:\u003c\/strong\u003e Cures to a high-strength, durable repair that matches or exceeds standard structural concrete.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e2-4 minute final set:\u003c\/strong\u003e Enables rapid successive placement when working from the outside in on large leaks, or when preparing joints for subsequent coatings.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eWater retention structures:\u003c\/strong\u003e Sealing water tanks, concrete pipes, culverts, and constructing pressure-resistant fillets at wall-to-floor junctions.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eSubterranean infrastructure:\u003c\/strong\u003e Stopping seepage in basements, cellars, underground car parks, lift pits, tunnels, power stations, and sewer systems.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eJoint filling:\u003c\/strong\u003e Filling joints between concrete segments in pipes, culverts, tunnels, and mines.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eFixtures:\u003c\/strong\u003e Anchoring bolts, conduits, pipes, and sanitary equipment into dense concrete.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eExpansion and movement joints:\u003c\/strong\u003e Do not use C-Plug as a sealant or filler over joints designed for structural movement.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eSubstrate compatibility:\u003c\/strong\u003e Only suitable for cementitious surfaces; do not apply over non-cementitious substrates.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eTemperature limits:\u003c\/strong\u003e Do not apply over frozen surfaces. Ensure all concrete and masonry surfaces exposed to freezing conditions are completely free of ice. Cold temperatures will slow the curing rate.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003ePreparation and installation\u003c\/h3\u003e\n \u003cp\u003eGrind open cracks, joints, or holes to a minimum width and depth of 20mm. For high-volume leaks, increase the cut depth to a minimum of 40mm. Cut sides to a square or dovetail profile where possible, avoiding \"V\" profiles, smooth finishes, or feathered edges. Flush the area with clean water to remove loose debris, and ensure the substrate is thoroughly damp before application.\u003c\/p\u003e\n \u003cp\u003eMix by hand using a spatula or similar tool; do not use electric stirrers or paddle mixers. Limit batch sizes to a maximum of one handful (approximately 0.5kg of powder) per application, using approximately 150ml of clean 20°C water per 1kg of product. Once mixed to a putty consistency, press C-Plug firmly into the cavity using a gloved hand. Hold firm pressure until the initial set occurs (30 to 60 seconds), then slowly remove your hand. Keep the cured plug damp using a mist spray or damp sponge for 15 minutes after installation.\u003c\/p\u003e\n\n \u003ch3\u003eSystem detailing\u003c\/h3\u003e\n \u003cp\u003eTo establish long-term protection against future dampness and negative water seepage in subterranean structures, coat the cured C-Plug with \u003ca href=\"\/products\/gripset-c-1p-1-part-flexible-cementitious-membrane\"\u003eGripset C-1P\u003c\/a\u003e flexible cementitious membrane. For active leaks at wall-to-floor junctions, cut out the joint to a minimum 20mm width, pack with C-Plug, and form a 45-degree, 40mm wide cove at the junction before over-coating with the membrane.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Gripset","offers":[{"title":"4 Kg","offer_id":39288856871104,"sku":"GRIPCPLUG\/4","price":51.96,"currency_code":"AUD","in_stock":true},{"title":"15 Kg","offer_id":39288856903872,"sku":"GRIPCPLUG\/15","price":155.87,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/gripset-c-plug-rapid-set-concrete-waterproofing-adheseal.png?v=1763709590"},{"product_id":"mountain-grout-gel-foam-4-litre","title":"Mountain Grout Gel Foam","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eFor sealing leaking cracks or joints in concrete structures with continuous moisture exposure, Mountain Grout Gel Foam is a hydrophilic polyurethane formulation that reacts with water to stop active leaks. The single-component system is formulated without TDI or solvents, reacting directly with the water it encounters inside the concrete to create either a foam or a gel barrier depending on the moisture volume present.\u003c\/p\u003e\n\u003ch3\u003eHow it works\u003c\/h3\u003e\n\u003cp\u003eMountain Grout Gel Foam can be pumped as a single component directly into wet concrete cracks, or injected as a dual-component system alongside water. Upon contact with water, the liquid expands up to 25 times its initial volume to fill voids and seal paths of water ingress. Because the formulation is hydrophilic, it requires continuous moisture exposure to maintain its physical seal, curing into an inert, non-toxic barrier that handles ongoing structural movement without losing adhesion.\u003c\/p\u003e\n\u003ch3\u003eWhere to use it\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eConcrete dams and tunnels experiencing water ingress\u003c\/li\u003e\n\u003cli\u003eStorm water systems and waste treatment plants\u003c\/li\u003e\n\u003cli\u003eUnderground vaults, elevator pits, and water-related facilities\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e400% elongation (ASTM D-638): High elasticity allows the cured gel-foam to stretch and flex with moving concrete joints and cracks without shearing the bond.\u003c\/li\u003e\n\u003cli\u003e650 cps viscosity (ASTM D-1638): Low viscosity allows the liquid grout to penetrate deep into fine cracks and fissures before reaction begins.\u003c\/li\u003e\n\u003cli\u003e30-second initiation time: Rapid start to the reaction when mixed at a 1:1 ratio with water at 25ºC, reaching full rise in approximately 6 minutes to choke off active water flows.\u003c\/li\u003e\n\u003cli\u003e170 psi tensile strength (ASTM D-638): Provides the mechanical strength necessary to withstand hydrostatic pressures in underground vaults and pits.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eLimitations\u003c\/h3\u003e\n\u003cul\u003e\u003cli\u003eFormulated for concrete structures with continuous moisture exposure; requires water to react and ongoing moisture to maintain its seal performance.\u003c\/li\u003e\u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Green Mountain International","offers":[{"title":"4 Kg","offer_id":46683174600896,"sku":"INJGELERA\/4","price":187.62,"currency_code":"AUD","in_stock":true},{"title":"20 Kg","offer_id":46683174633664,"sku":"INJGELERA\/20","price":485.34,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/mountain-grout-gel-foam-crack-injection-sealant-adheseal.png?v=1763709590"},{"product_id":"mountain-grout-flexible","title":"Mountain Grout Flexible","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eFor sealing leaking cracks and failed joints in concrete structures under wet\/dry cycles, Mountain Grout Flexible provides a hydrophobic barrier that resists shrinkage. When injected into storm water systems, tunnels, manholes, or concrete dams, this closed-cell polyurethane foam reacts with moisture to form an inert, permanent seal that accommodates structural movement without losing adhesion.\u003c\/p\u003e\n\u003ch3\u003eHow it works\u003c\/h3\u003e\n\u003cp\u003eMountain Grout Flexible is a low-viscosity, hydrophobic polyurethane system consisting of an amber base resin and Accelerator B. Unlike hydrophilic grouts that require constant moisture to maintain their volume, this hydrophobic formulation reacts with minimal water to form a stable closed-cell foam. Because the cured grout does not rely on retained water, it will not shrink or lose its seal when water tables drop or joints dry out. The system pumps as a single component after mixing the base resin and accelerator, allowing the installer to adjust the reaction profile on-site to match the water flow and temperature of the concrete substrate.\u003c\/p\u003e\n\u003ch3\u003eWhere to use it\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eConcrete dams and earthen dams\u003c\/li\u003e\n\u003cli\u003eWaste treatment plants and water-related facilities\u003c\/li\u003e\n\u003cli\u003eStorm water systems and manhole facilities\u003c\/li\u003e\n\u003cli\u003eTunnels and underground vaults\u003c\/li\u003e\n\u003cli\u003eElevator pits and parking garages\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e44% elongation (ASTM D-638):\u003c\/strong\u003e High flexibility to absorb joint expansion and contraction in concrete structures without tearing or delaminating.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp to 30x expansion:\u003c\/strong\u003e Expands up to 30 times its initial liquid volume to fill deep voids and wide cracks behind leaking concrete walls.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e\u0026lt;1% water absorption (ASTM D-2842):\u003c\/strong\u003e Highly impermeable closed-cell structure prevents water migration through the cured seal.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e500 cps base viscosity (ASTM D-1638):\u003c\/strong\u003e Low viscosity allows deep penetration into fine fractures and tight concrete joints before reaction begins.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e15-second to 50-second initiation windows:\u003c\/strong\u003e Reaction speeds are controlled by the dosage of Accelerator B at 25ºC, letting installers match the foam rise to the water pressure.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eControlling reaction times\u003c\/h3\u003e\n\u003cp\u003eThe reaction profile must be adjusted prior to pumping by mixing Accelerator B into the base resin. The speed of the expansion is determined by the accelerator dosage, substrate temperature, and the amount of moisture encountered. At 25ºC, the reaction times are:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAt 1.25% dosage (1\/2 pint per 5 gallons):\u003c\/strong\u003e Expansion starts in approximately 50 seconds and completes in approximately 4 minutes after encountering water.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAt 2.5% dosage (1 pint per 5 gallons):\u003c\/strong\u003e Expansion starts in approximately 15 seconds and completes in approximately 65 seconds after encountering water.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Green Mountain International","offers":[{"title":"4 Kg","offer_id":46683135738048,"sku":"INJFLEXERA\/4","price":187.62,"currency_code":"AUD","in_stock":true},{"title":"20 Kg","offer_id":46683135770816,"sku":"INJFLEXERA\/20","price":485.34,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/mountain-grout-flexible-polyurethane-crack-injection-adhesea.png?v=1763709590"},{"product_id":"gripset-11y","title":"Gripset 11Y Admixture","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor cement screeds, renders, and patch mortars exposed to weather, continuous immersion, or underground dampness, Gripset 11Y is a concentrated SBR latex polymer admixture that improves adhesion, flexural strength, and water resistance. It prevents water-pathway failures in demanding wet areas, reduces the occurrence of efflorescence in screeds, and acts as a high-bond slurry primer over porous concrete, masonry, and blockwork.\u003c\/p\u003e\n\n \u003ch3\u003eWhat it does\u003c\/h3\u003e\n \u003cp\u003eGripset 11Y modifies cement-based compounds by replacing a portion of the mixing water with SBR latex polymer. This polymer network forms within the curing cement matrix, reducing the water-to-cement ratio and closing down the capillary pathways that allow water and salt migration. The result is a highly dense mortar or screed with reduced permeability to liquids and gases, increased resistance to freeze-thaw cycles, and higher early strength development. It also increases flexural strength and durability, allowing thin-build repairs and screeds to withstand movement without cracking or delaminating from the substrate.\u003c\/p\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eSubstrates:\u003c\/strong\u003e Concrete, masonry, renders, screeds, concrete blocks, aerated concrete, clay bricks, pavers, cement sheeting, marine plywood, wet-area particle board, asphalt, cured bitumen surfaces, and existing acrylic coatings or Gripset membranes.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eApplications:\u003c\/strong\u003e Waterproofing slurry coats, water-resistant screeds and renders, patch mortars in immersed areas, and as an adhesion and water-resistance enhancer for cement-based tile adhesives and grouts in harsh climatic conditions.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e1.0mm wet film thickness:\u003c\/strong\u003e The target application thickness when mixed as a high-bonding primer or sealing slurry to ensure a continuous, protective barrier.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e1 litre per 3m² coverage:\u003c\/strong\u003e The consumption rate of Gripset 11Y when mixed and applied as a primer slurry, helping you calculate material requirements for substrate preparation.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e3mm minimum build:\u003c\/strong\u003e The lowest allowable thickness when applying mixed 11Y patch mortars as thin-build coatings in immersed or wet areas.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e1:3 liquid-to-water ratio:\u003c\/strong\u003e The mixing ratio for screeds, renders, adhesives, and grouts to ensure correct polymer distribution without over-diluting the binder.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e1:1 liquid-to-water ratio:\u003c\/strong\u003e The concentrated mixing ratio required for high-adhesion, water-resistant patch mortars.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eHow to apply\u003c\/h3\u003e\n \u003cp\u003eFor all applications, substrates must be clean, sound, dry, and free of dust, oil, grease, curing compounds, release agents, and loose material. Mechanically remove structurally unsound layers by grinding or abrasive blasting. If the substrate is subject to active moisture or rising damp, treat it with \u003ca href=\"\/products\/gripset-e60\"\u003eGripset E60\u003c\/a\u003e before application.\u003c\/p\u003e\n \u003cp\u003eWhen applying screeds, renders, or patch mortars, first prime the surface with the 11Y Primer\/sealing slurry. For optimum adhesion, apply the screed or mortar directly onto the wet or damp primer using a \"wet-on-wet\" method. Wash all tools with water immediately after use; dried material must be removed mechanically.\u003c\/p\u003e\n\n \u003ch3\u003eMix designs\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003ePrimer \/ Sealing Slurry:\u003c\/strong\u003e Mix 1 part Gripset 11Y, 1 part wash sand, and 1 part cement by volume. Mix slowly with an electric paddle mixer to a fluid consistency, let settle for 3 to 4 minutes, then re-stir lightly before applying by brush, roller, broom, or squeegee.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eHigh-Performance Screeds \u0026amp; Renders:\u003c\/strong\u003e Mix dry ingredients of 1 part cement and 4 parts fine wash grade sand. Combine with a mixing liquid of 1 part Gripset 11Y to 3 parts water.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003ePatch Mortars:\u003c\/strong\u003e Mix dry ingredients of 1 part cement and 3 parts fine wash grade sand. Combine with a mixing liquid of 1 part Gripset 11Y to 1 part water.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not use on glass or glazed surfaces.\u003c\/li\u003e\n \u003cli\u003eDo not apply over raw steel or metals unless specified.\u003c\/li\u003e\n \u003cli\u003eDo not use for priming areas subject to rising moisture or negative hydrostatic pressure.\u003c\/li\u003e\n \u003cli\u003eWhen using as a bonding agent, always use sharp wash-grade sand and fresh Portland cement.\u003c\/li\u003e\n \u003cli\u003eConsult RLA Technical Department before applying over existing paints, membranes, coatings, or other finished surfaces to confirm suitability and preparation.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Gripset","offers":[{"title":"5L","offer_id":46349641056448,"sku":"PRIMEGRIP11Y\/5","price":99.49,"currency_code":"AUD","in_stock":true},{"title":"15L","offer_id":46194451808448,"sku":"PRIMEGRIP11Y\/15","price":218.09,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/gripset-11y-sbr-waterproofing-adhesive-screeds-adheseal.png?v=1763710065"},{"product_id":"efflock-concentrate","title":"Efflock Hydrophobic Additive","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eFor bathroom tiling, balconies, pool surrounds, and stonemasonry where salt damp or calcium carbonate stains threaten the finish, Hydrophobic Additive provides permanent protection by treating the entire concrete mass. Added directly to the mix, this water-based liquid creates an invisible hydrophobic molecular structure within the pores of cement-based materials to lock out efflorescence without blocking vapour permeability.\u003c\/p\u003e\n\u003ch3\u003eWhat it does\u003c\/h3\u003e\n\u003cp\u003eHydrophobic Additive acts as a bulk impregnating agent that repels liquid water while remaining breathable. By preventing the capillary action that draws moisture through concrete, brick, sandstone, and porous masonry, it stops waterborne salts from migrating to the surface. This mechanical control prevents picture framing in granite and basalt paving, stops salt attack in saline soils, and deprives moss and mould of the moisture required to grow on off-form concrete or brickwork. Unlike topical sealers, bulk impregnation protects the entire mass, meaning the water-repellent performance is unaffected by traffic wear, surface abrasion, or minor movement cracks.\u003c\/p\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1:100 dilution ratio:\u003c\/strong\u003e 1 part Hydrophobic Additive to 100 parts clean water (or 100ml per 100L screed mixer capacity) provides a highly concentrated formula that minimizes packaging waste on site.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e16m² coverage:\u003c\/strong\u003e 1 litre treats approximately 16m² of tiling, which covers a 40mm thick tile screed, tile adhesive, and tile grout based on a 300 x 300 x 10mm floor tile.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24-hour rain window:\u003c\/strong\u003e Treated cement-based materials must cure for up to 24 hours before any exposure to rain to ensure the hydrophobic barrier forms correctly.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e4°C to 35°C application range:\u003c\/strong\u003e Air and substrate temperatures must remain within this window during application and initial curing.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhere to use it\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTiled wet areas:\u003c\/strong\u003e For screeds, adhesives, and grouts in bathrooms, balconies, patios, stairs, and pool surrounds to prevent efflorescence and protect primary waterproofing membranes from water pooling underneath tiles.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStonemasonry and brickwork:\u003c\/strong\u003e Mixed into mortar to form a built-in damp proof course (DPC) that blocks rising damp and salt attack, particularly when using white cement.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConcrete structures:\u003c\/strong\u003e Protects off-form concrete, post-tension reinforcement pockets, and concrete pavers against freeze-thaw damage and chloride ion absorption.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInstallation limits\u003c\/h3\u003e\n\u003cp\u003eAlways use General Purpose Cement (Type GP) for applications where efflorescence is a risk. Do not use Builders Cement (Type GB); its high proportion of fly ash or blast furnace slag contributes to efflorescence and works against hydrophobic additives. \u003c\/p\u003e\n\u003cp\u003eWhen mixing tile screed, sand from the building yard carries variable moisture that pre-dilutes the mix. To maintain correct dosage, add Hydrophobic Additive neat to the screed mixer at 100ml per 100L of mixer capacity, then add water to reach the desired consistency. For hand-mixed screeds, pre-gauge in a bucket with a tighter 1:80 or 1:50 dilution to compensate for wet sand.\u003c\/p\u003e\n\u003cp\u003eLatex additives used in cement slurries or tile adhesives will delay the water-repellent performance of Hydrophobic Additive for approximately 6 days. While compatible, the system will not exhibit full hydrophobicity during this initial cure window. If rain enters tile adhesive notches before grouting, extract it with a vacuum and allow it to evaporate fully.\u003c\/p\u003e\n\u003cp\u003eSupervisors should water-test all screeds, mortars, and concrete after 24 hours. A successful mix will show a distinct water-beading effect; if the substrate absorbs water, seek technical advice before proceeding.\u003c\/p\u003e\n\u003ch3\u003eCautions and limitations\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eNo hydrostatic pressure rating:\u003c\/strong\u003e Hydrophobic Additive does not fill concrete pores and is not rated to resist head pressure under continuous underwater immersion.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStain limits:\u003c\/strong\u003e The hydrophobic barrier repels waterborne contaminants but is not effective against oil-based stains.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDark grouts:\u003c\/strong\u003e The additive does not resolve or contribute to the patchy appearance or colour-retention issues inherent to dark proprietary grouts.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNatural stone migration:\u003c\/strong\u003e On highly porous stone or certain dark stones like G684 basalt and sandstone, the additive can migrate from wet bedding screeds or grout into the stone, creating visible dry spots when the stone gets wet. This must be prevented by pre-sealing the stone, or by applying grout across the entire face of the stone rather than just the joints.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNo 6-sided sealing on low porosity:\u003c\/strong\u003e Do not apply sealers to the bedding face of low-porosity stone, as active sealer ingredients sitting on the surface will cause adhesion failure.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAcid cleaning adjustment:\u003c\/strong\u003e Hydrophobic Additive in mortar repels water but does not repel hydrochloric acid. For face brickwork cleaning, the standard acid-to-water dilution ratio may need to be strengthened to compensate for the water repellency of the mortar joint.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Efflock","offers":[{"title":"1 Litre","offer_id":44688346742976,"sku":"EFFLOCK\/1","price":102.17,"currency_code":"AUD","in_stock":true},{"title":"5 Litres","offer_id":46349640892608,"sku":"EFFLOCK\/5","price":429.16,"currency_code":"AUD","in_stock":true},{"title":"20 Litres","offer_id":46349640925376,"sku":"EFFLOCK\/20","price":1550.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/efflock-hydrophobic-sealer-efflorescence-adheseal.png?v=1763710206"},{"product_id":"armadillo-d","title":"Armadillo D","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor warehouse floors, manufacturing plants, and residential garages where dusting, rain damage, or weak mortar has compromised the concrete, Armadillo D penetrates the surface to increase abrasion resistance and seal the substrate. This water-based silicate compound chemically converts soft, porous calcium hydroxide into high-strength calcium silicate hydrate, binding with the concrete matrix to provide permanent surface hardening.\u003c\/p\u003e\n\n \u003ch3\u003eHow it works\u003c\/h3\u003e\n \u003cp\u003eArmadillo D penetrates the concrete pores to react with free lime (calcium hydroxide), which is highly susceptible to carbonation and wear. By converting this soft mineral into calcium silicate hydrate (CSH)—the primary load-bearing phase of concrete paste—it densifies the surface from within. This chemical integration prevents dusting, reduces liquid absorption, and slows down carbon dioxide ingress to protect old carbonated concrete from further degradation. It dries transparent and allows after-trades installation, making it compatible with carpet adhesives, tiling, line marking, and tilt-up bond breakers.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e4 to 5 m² per litre:\u003c\/strong\u003e Expected coverage rate on steel-trowelled concrete, varying based on the porosity and surface texture of the slab.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e4 to 6 hours:\u003c\/strong\u003e Required drying time before permitting light foot traffic at 21°C and 50% relative humidity.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e24 hours:\u003c\/strong\u003e Minimum drying window required before opening the treated surface to wheel traffic.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e24 to 72 hours:\u003c\/strong\u003e Curing window during which the concrete gradually darkens and increases in impermeability to oils and water.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e4 weeks:\u003c\/strong\u003e Necessary hardening and curing period for newly placed concrete before applying paint or floor coverings.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eNew concrete:\u003c\/strong\u003e Can be applied at the time of pour as a curing and densifying compound, or used with traditional curing methods.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eExisting concrete slabs:\u003c\/strong\u003e Suitable for interior or exterior environments, commercial warehouse floors, and residential basements to repair rain-damaged surfaces or weak, carbonated concrete.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eJoint treatment:\u003c\/strong\u003e Can be applied over soft-cut saw joints, including flooding the joints, once excess cement dust is removed.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eApplication methods\u003c\/h3\u003e\n \u003cp\u003eFor new concrete at the time of pour, apply the liquid by broom or low-pressure sprayer (dispensing at 250–500 kPa) as soon as the surface is firm enough to walk on. Keep the surface wet for 30 minutes, working it in with a soft-bristled broom. When it becomes slippery, mist lightly with water. Once slippery again, flush thoroughly with water and squeegee completely dry to remove all alkali residue. For exterior broom-finished slabs, squeegee or sweep excess material off after 30 to 40 minutes without flushing.\u003c\/p\u003e\n \u003cp\u003eFor existing slabs, clean the concrete of all contaminants. Apply at approximately 5 m²\/L, scrubbing the product into the surface with a mechanical scrubber on large areas, or using a watering can and bristle broom on small perimeters. Keep wet for up to 60 minutes, then squeegee and vacuum any excess material onto the next section. Do not allow excess puddles to dry on the slab.\u003c\/p\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not leave any excess Armadillo D residue on the treated concrete surface; hardened excess material must be removed mechanically with a grinder.\u003c\/li\u003e\n \u003cli\u003eArmadillo D does not meet the curing requirements of AS 3799 on its own. For compliant curing on new concrete, Surface Cure R must be applied after the excess silica treatment has dried.\u003c\/li\u003e\n \u003cli\u003eThis product is not a rising damp barrier; its function is restricted to dustproofing and abrasion resistance.\u003c\/li\u003e\n \u003cli\u003eIncompatible with aluminum, copper, brass, bronze, zinc, tin, and their alloys, which it will corrode.\u003c\/li\u003e\n \u003cli\u003eProtect adjacent glass, metal, wood, paint, and brick from overspray; wash immediately with potable water if contact occurs.\u003c\/li\u003e\n \u003cli\u003eDo not load or store with Class 4.3 (dangerous when wet) substances, Class 5 (oxidising agents), or foodstuffs. Protect the liquid from freezing.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Armadillo","offers":[{"title":"Default Title","offer_id":46158253654208,"sku":"ARMA\/20","price":283.67,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/armadillo-d-concrete-densifier-dustproof-adheseal.png?v=1763710783"},{"product_id":"rla-fairing-coat-mortar","title":"RLA Penapatch Fairing Coat Mortar","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eFor thin-layer repairs over surface imperfections, RLA Penapatch Fairing Coat Mortar provides a smooth, fine-textured finish on concrete, masonry, and existing RLA mortars. Formulated with a blend of cement and polymers, this compound achieves rapid early strength with minimal shrinkage, producing a surface that does not telegraph or show through overlaid architectural coatings. It is suitable for both internal and external vertical applications, and can be left exposed as a stand-alone final coat or overcoated with protective finishes.\u003c\/p\u003e\n\u003ch3\u003eHow it works\u003c\/h3\u003e\n\u003cp\u003ePenapatch Fairing Coat Mortar relies on a polymer-modified cementitious design to achieve excellent adhesion to mineral substrates without requiring a separate bonding agent under standard conditions. The fast-setting chemistry achieves a 20 MPa compressive strength at 28 days while maintaining a low drying shrinkage profile of less than 300 microstrain, preventing fine cracking across thin applications up to 5mm deep. When applied over other repair mortars, it fills surface blemishes, voids, and defects to create a uniform, paint-ready substrate.\u003c\/p\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e5mm maximum depth:\u003c\/strong\u003e The maximum allowable thickness per single application to prevent curing issues, though it can be successfully feather-edged in patch repairs.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e25-minute initial set time:\u003c\/strong\u003e The active work window at 20°C to apply and finish the mortar before it begins to stiffen.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e20 MPa compressive strength:\u003c\/strong\u003e Verified at 28 days (tested to AS1012 \u0026amp; AS2073) to ensure a durable, structurally stable repair layer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e48-hour cure window for finishes:\u003c\/strong\u003e The minimum waiting time at 10°C to 35°C before applying decorative or protective coatings. Applications under 10°C require an additional 24 hours of curing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e14-litre yield:\u003c\/strong\u003e The volume produced per 20kg bag when mixed with the specified 5.9 to 6.0 litres of water.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhere to use it\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eInfilling blowholes, surface imperfections, and defects on concrete surfaces.\u003c\/li\u003e\n\u003cli\u003eDressing vertical concrete and masonry faces to achieve a smooth finish.\u003c\/li\u003e\n\u003cli\u003ePlacing a skim coat over existing RLA mortars to establish a uniform surface.\u003c\/li\u003e\n\u003cli\u003eInternal and external walls requiring a stand-alone, exposed final finish.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eLimitations\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDo not use in areas subject to rising dampness or in wet areas.\u003c\/li\u003e\n\u003cli\u003eDo not apply at temperatures below 5°C and falling, or above 35°C.\u003c\/li\u003e\n\u003cli\u003eThe product will not bridge structural movement; if the underlying substrate moves or cracks, reflective cracks will transfer through the mortar.\u003c\/li\u003e\n\u003cli\u003eDo not add excess water beyond the specified 5.9 to 6.0 litres per bag, as this extends cure times and reduces final strength.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eApplication and curing\u003c\/h3\u003e\n\u003cp\u003eEnsure the substrate is fully cured (new concrete must be cured at least 21 days), clean, and free of laitance or bond-inhibiting contaminants. Remove weak concrete and use scabbling or water blasting to establish a mechanical key. Pre-soak the surface with clean water, ensuring no free-standing water remains before application.\u003c\/p\u003e\n\u003cp\u003eFor highly porous surfaces, apply \u003ca href=\"\/products\/rla-primer-rendergrip-a\"\u003eRLA Rendergrip\u003c\/a\u003e A prior to pre-soaking to prevent the mortar from flash drying and to preserve workability. Mix the mortar using a forced action drill mixer and paddle, slowly adding the powder to 5.9 to 6.0 litres of water to prevent lumping. Apply by trowel to the desired thickness up to 5mm. Do not overwork the surface or re-temper partially set product. In warm conditions, high winds, or direct sun, apply RLA Rendergrip A as a curing compound immediately after the final trowel to prevent premature drying.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"RLA","offers":[{"title":"Default Title","offer_id":46203631304896,"sku":"MORTARRLAFC\/20","price":78.94,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/RLAMFC.png?v=1754479985"},{"product_id":"rla-mortar-penapatch-hb50","title":"RLA Penapatch HB50 Mortar","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor high-build structural concrete restoration on vertical, horizontal, or overhead faces, \u003ca href=\"\/products\/rla-penapatch\"\u003ePenapatch\u003c\/a\u003e HB50 Mortar provides a shrinkage-compensated, medium-weight repair barrier. It is formulated to reinstate structural integrity in damaged concrete panels and spalled areas caused by reinforcing steel corrosion, reaching a high ultimate compressive strength of 55 MPa at 28 days without requiring formwork for standard vertical builds up to 80mm.\u003c\/p\u003e\n\n \u003ch3\u003eWhat it does\u003c\/h3\u003e\n \u003cp\u003ePenapatch HB50 Mortar forms a low-permeability barrier that resists carbon dioxide and chloride intrusion, protecting embedded steel rebar from carbonation and corrosion. The polymer-modified cementitious design provides high adhesion to concrete and masonry substrates while managing drying shrinkage (under 350 micro-strain at 28 days) to prevent edge curling or separation. It can be applied manually with a trowel or gloved hand, or wet-sprayed and pumped through a nozzle for larger-scale compaction on site.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e55 MPa compressive strength (at 28 days, AS1478.2-2005):\u003c\/strong\u003e High ultimate load-bearing strength to match or exceed structural concrete requirements.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e5mm to 80mm vertical thickness:\u003c\/strong\u003e High-build vertical placement in a single application without slumping; extendable up to 120mm in small pockets or with formwork.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e3.0 litres water limit:\u003c\/strong\u003e Strict mixing water ceiling per 20kg bag to maintain high-build sag resistance and prevent loss of compressive strength.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e2-hour initial \/ 4-hour final set (at 20°C):\u003c\/strong\u003e Predictable working window to place, compact, and finish the mortar before curing begins.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e100 Wear Index (at 28 days, ASTM CS01-1984):\u003c\/strong\u003e High abrasion resistance under service loads, compared to a standard 40-50 MPa concrete index of 71.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eStructural concrete panels:\u003c\/strong\u003e Repairing damaged, chipped, or spalled precast and in-situ panels.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eReinforcing steel repairs:\u003c\/strong\u003e Patching spalled concrete caused by expanding, corroding rebar.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eDeep horizontal fills:\u003c\/strong\u003e Horizontal concrete repairs up to 120mm deep.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eChloride-exposed zones:\u003c\/strong\u003e Infrastructure requiring low-permeability protection against marine or salt-laden environments.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eHow to apply\u003c\/h3\u003e\n \u003cp\u003ePrepare the substrate to a minimum depth of 5mm to avoid feather-edging, breaking out up to a clean saw-cut edge. Remove all weak concrete, laitance, and contamination by scabbing or high-pressure water blasting. Clean any corroded steel rebar to a bright condition using grit blasting, and prime immediately with RLA Zinc Rich Primer, ensuring the zinc primer does not contact the host concrete.\u003c\/p\u003e\n \u003cp\u003ePrime concrete and masonry surfaces with \u003ca href=\"\/products\/rla-primer-rendergrip-a\"\u003eRLA Rendergrip\u003c\/a\u003e A Bonding Agent and Primer, allowing it to reach a tacky consistency before mortar application. If the primer dries, it must be re-applied. For porous substrates, pre-soak with water and remove excess before priming. For repairs exposed to permanent or occasional dampness, or for fully immersed applications, prime the substrate with RLA Epilox Binder.\u003c\/p\u003e\n \u003cp\u003eMix using a mechanical forced-action mixer with a high-shear spiral paddle. Do not use free-fall mixers, do not mix part bags, and do not hand-mix. Add the 20kg powder to exactly 3.0 litres of clean water and mix for 3 to 5 minutes until homogenous. Compact the mortar thoroughly into the substrate and around exposed rebar, finishing with a steel trowel without overworking the surface. Cure using RLA Curecon A in accordance with good concrete practice. Decorative or protective coatings may be applied directly over the cured surface.\u003c\/p\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not apply at temperatures below 5°C or above 35°C. Use warm water at 5°C and below, and chilled water above 35°C to control initial set.\u003c\/li\u003e\n \u003cli\u003eDo not exceed 3.0 litres of water per 20kg bag; excess water increases mortar sag, reduces final strength, and extends drying time.\u003c\/li\u003e\n \u003cli\u003eDo not apply in layers less than 5mm thick, except in very localized, occasional areas.\u003c\/li\u003e\n \u003cli\u003eExisting concrete substrates must be at least 21 days old before application.\u003c\/li\u003e\n \u003cli\u003eIf the host substrate moves or cracks, reflective cracking will occur in the repair mortar.\u003c\/li\u003e\n \u003cli\u003eProtect the wet mortar from direct sunlight, high winds, and rain or water contact for a minimum of 24 hours.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"RLA","offers":[{"title":"Default Title","offer_id":46203666399424,"sku":"MORTARRLAHB50\/20","price":85.68,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/RLAHB50.png?v=1754479984"},{"product_id":"rla-penapatch","title":"RLA Penapatch HB80 Mortar","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor structural repairs on concrete panels, spalled masonry, and corroded rebar, Penapatch HB80 Mortar is a shrinkage-compensated, polymer-modified structural mortar. It is formulated to achieve high-build vertical and overhead repairs without slumping, restoring structural integrity to damaged substrates while providing low permeability to protect steel reinforcement from chloride attack and carbonation.\u003c\/p\u003e\n\n \u003ch3\u003eHow it works\u003c\/h3\u003e\n \u003cp\u003ePenapatch HB80 Mortar uses a blend of cements and polymers to form a dense, high-compressive-strength mortar that bonds tenaciously to concrete and masonry. The shrinkage-compensated formulation ensures dimensional stability over the long term, preventing the shrinkage cracking common in standard sand-and-cement mortar repairs. Its high build capability allows installers to rebuild vertical surfaces up to 80mm in a single pass without using formwork, or up to 160mm in small pockets or when supported by temporary forms.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e68 MPa compressive strength (at 28 days, AS1478.2-2005):\u003c\/strong\u003e High structural capacity to support loads on structural concrete panels and columns.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e10 MPa flexural strength (at 28 days, AS1012-11-2000):\u003c\/strong\u003e Resists bending stresses under load without cracking at the repair boundaries.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e5mm to 100mm vertical build (up to 180mm horizontal):\u003c\/strong\u003e Allows thick single-application repairs, reducing the need for multi-layer build-ups.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e1.5 hours initial \/ 2.5 hours final set time (at 20°C):\u003c\/strong\u003e Provides an efficient work window before setting, minimizing downtime before subsequent finishes can be considered.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e3.6 litres of water per 20kg bag:\u003c\/strong\u003e Precise water-to-powder ratio required to prevent sag, preserve compressive strength, and control drying shrinkage.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cp\u003eThis repair mortar is suitable for internal or external applications on concrete, masonry, steel, and rebar. Common structural repairs include:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003eRebuilding spalled or deteriorated concrete caused by rusted, expanding steel reinforcement.\u003c\/li\u003e\n \u003cli\u003eRepairing chipped, cracked, or damaged structural concrete panels.\u003c\/li\u003e\n \u003cli\u003eOverhead, vertical, and horizontal patching where high abrasion resistance is required.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eSystem components\u003c\/h3\u003e\n \u003cp\u003eFor a complete structural repair, Penapatch HB80 Mortar must be used with the following system components as specified by the substrate and service conditions:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eRLA Zinc Rich Primer:\u003c\/strong\u003e Applied directly to grit-blasted steel and rebar to stop further oxidation and rust.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/products\/rla-primer-rendergrip-a\"\u003eRLA Rendergrip\u003c\/a\u003e A Bonding Agent and Primer:\u003c\/strong\u003e Standard host concrete primer. Apply the mortar while Rendergrip A is tacky. If the primer dries, it must be reapplied. Do not apply over wet primer to avoid slumping.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eRLA Epilox Binder:\u003c\/strong\u003e Required as the substrate primer for damp repairs, areas exposed to occasional or permanent water, or under fully immersed conditions. Apply the mortar while the binder is tacky, not dry.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eRLA Curecon A:\u003c\/strong\u003e Curing compound applied after the final trowel to ensure correct cement hydration, especially in high-wind or exposed conditions.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eConcrete substrates must be at least 21 days old before application.\u003c\/li\u003e\n \u003cli\u003eDo not apply in areas less than 5mm thick, except in very localised spots.\u003c\/li\u003e\n \u003cli\u003eDo not use when ambient temperatures are below 5°C or above 35°C.\u003c\/li\u003e\n \u003cli\u003eEnsure the repaired area does not contact water or rain for at least 24 hours after application.\u003c\/li\u003e\n \u003cli\u003eIf the host substrate moves or cracks, reflective cracking will appear in the cured mortar.\u003c\/li\u003e\n \u003cli\u003eDo not mix part bags, mix by hand, or add more than 3.6 litres of water per bag, as excess water reduces final strength and increases drying shrinkage.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"RLA","offers":[{"title":"Default Title","offer_id":46203676295360,"sku":"MORTARRLAHB80\/20","price":97.41,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/RLAHB80.png?v=1754479983"},{"product_id":"cement-australia-sand-cement","title":"Cement Australia Sand \u0026 Cement (Screed)","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor setting shower bases and toilet pans, bedding pavers, or patching concrete walls, brickwork, and rendered surfaces, Sand \u0026amp; Cement (Screed) provides a pre-blended, general-purpose mortar. This \"Just Add Water\" mix combines graded sands and cement in predetermined ratios, eliminating the need to source and proportion raw materials on site.\u003c\/p\u003e\n\n \u003ch3\u003eWhat it does\u003c\/h3\u003e\n \u003cp\u003eSand \u0026amp; Cement (Screed) functions as a stable bedding and repair mortar. It delivers a reliable consistency for plumbing installations, landscaping edge work, and vertical patching on brickwork or rendered surfaces. By adding clean drinking water, the dry mix forms a workable paste that can be finished with a sponge, steel trowel, or wooden float once it sets touch-dry.\u003c\/p\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003ePlumbing:\u003c\/strong\u003e Setting and securing shower bases and toilet pans.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003ePaving and landscaping:\u003c\/strong\u003e Bedding and joint filling of pavers, and bedding garden edges or rockeries.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eRepairs:\u003c\/strong\u003e Patching concrete walls, brickwork, and rendered surfaces.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eGeneral bricklaying:\u003c\/strong\u003e Suitable for basic masonry, though specific structural modifications may be required depending on the application.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e1.1m² coverage:\u003c\/strong\u003e The approximate coverage achieved by one 20kg bag when applied at a thickness of 10mm.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e24-hour curing floor:\u003c\/strong\u003e Do not walk on or load paths, slabs, or edges for at least 24 hours after placement to allow the mortar to develop sufficient early strength.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e6-month shelf life:\u003c\/strong\u003e Recommended storage limit from the date of manufacture when stored unopened in a dry place off the ground. Once opened, the bag must be used that day.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eExcess water:\u003c\/strong\u003e Adding too much water during mixing weakens the overall final strength of the mortar.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eBricklaying modification:\u003c\/strong\u003e For general bricklaying, adding lime is recommended. For dedicated masonry work, using Cement Australia Mortar Mix is more appropriate.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eRendering limits:\u003c\/strong\u003e For superior rendering results, use a product from the Cement Australia Render It range.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003ePot life management:\u003c\/strong\u003e Never mix more material than can be used within a reasonable time limit.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eApplication guide\u003c\/h3\u003e\n \u003cp\u003ePrepare the receiving concrete, brickwork, or rendered surface by ensuring it is clean and free of oils, grease, dust, and loose debris. Empty the dry mix into a wheelbarrow, concrete mixer, or non-porous vessel. Add clean drinking water gradually while blending thoroughly to achieve a workable consistency. After placing, allow the mortar to set to touch-dry before completing the final finish with a clean damp sponge, steel trowel, or wooden float. Clean all tools with water immediately after use.\u003c\/p\u003e\n\n \u003cp\u003eIf colouring is required, add Cement Australia Oxide colours directly to the mix. Ensure all ingredients, particularly the oxide and water, are measured identically across subsequent batches to prevent shade variations.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Cement Australia","offers":[{"title":"Default Title","offer_id":46211716907200,"sku":"SANDNCEMENT\/20","price":12.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/Cement_Australia_Sand_Cement_Image.png?v=1754479981"},{"product_id":"planitop-fine-finish","title":"Planitop Fine Finish Mortar","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eFor smoothing porous or uneven concrete structures, Planitop Fine Finish Mortar provides a rapid-hardening, ultra-fine finish before painting or sealing. It is formulated to level surface defects in cast concrete, such as gravel clusters and second pours, as well as skimming precast elements including buffer panels, beams, and pillars.\u003c\/p\u003e\n\u003ch3\u003eWhat it does\u003c\/h3\u003e\n\u003cp\u003ePlanitop Fine Finish Mortar forms a thixotropic, trowellable paste that can be skimmed down to a feather edge without a bonding promoter, or applied in layers up to 3 mm thick. Its 0.2 mm maximum aggregate size creates an ultra-fine texture that makes finishing with a damp sponge float or spreader easier. The cured mortar functions as a concrete surface protection system conforming to EN 1504-2 coating (C) standards under principles MC and IR.\u003c\/p\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e0 to 3 mm thickness:\u003c\/strong\u003e Allows feather-edge skimming to level superficial defects up to a maximum 3 mm application depth.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e8.0 to 8.4 litres of water:\u003c\/strong\u003e The exact mixing ratio per 20 kg bag (40% to 42% water by weight) required to achieve a stable, thixotropic consistency.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e45-minute pot life:\u003c\/strong\u003e The working window at +23°C and 50% relative humidity before the mixed mortar begins to set.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e12 MPa compressive strength:\u003c\/strong\u003e Reaches 5 MPa after 1 day, 8 MPa after 7 days, and 12 MPa at 28 days for durable surface integration.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e7-day paint window:\u003c\/strong\u003e Minimum waiting time required before coating the finished surface with Elastocolor or Colorite paint lines.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1.2 kg\/m² consumption:\u003c\/strong\u003e Coverage rate per millimetre of thickness, allowing precise job estimation.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhere to use it\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCast concrete:\u003c\/strong\u003e Levelling gravel clusters, tie-rod holes, and cold joints.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrecast concrete:\u003c\/strong\u003e Skimming beams, pillars, and buffer panels to achieve a uniform finish.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConcrete walls:\u003c\/strong\u003e Smoothing and filling imperfections on internal and external walls before applying paint or protective coatings.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eLimitations\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDo not mix with more than the recommended amount of water and never add more water once setting has started.\u003c\/li\u003e\n\u003cli\u003eDo not apply if the temperature is lower than +5°C.\u003c\/li\u003e\n\u003cli\u003eDo not add lime, cement, or gypsum to the mix.\u003c\/li\u003e\n\u003cli\u003eDo not use on surfaces exposed to direct sunlight or strong winds.\u003c\/li\u003e\n\u003cli\u003eDo not apply on substrates with rising damp or free-standing surface water.\u003c\/li\u003e\n\u003cli\u003eUse Mapefinish or Mapefinish HD instead for hydraulic structures or surfaces subjected to abrasion.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003cp\u003ePrepare the concrete substrate by removing all loose material with power tools, wash thoroughly with water to remove dust, and wait until excess water evaporates. The substrate must be saturated but have a dry surface (saturated surface dry, or s.s.d. condition). Mix by pouring 8.0 to 8.4 litres of clean water into a container and slowly adding the 20 kg bag while mixing with a low-speed mechanical mixer to prevent air entrained in the mix. Spread the mortar up to 3 mm thick with a rubber or smooth metal spreader, and finish with a damp sponge float a few minutes after application. In hot, dry, or windy conditions, spray water on the touch-dry surface and repeat over the following days to prevent quick drying and plastic shrinkage cracks.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Mapei","offers":[{"title":"Default Title","offer_id":46558643028160,"sku":"MAPEIPLANITOPFF\/20","price":107.31,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/MapeiPlanitopFineFinishProductImage.png?v=1754479966"},{"product_id":"mapegrout-fast-set-rapido","title":"Mapegrout Fast-Set Rapido","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor rapid concrete repairs on exterior vertical or horizontal surfaces, Mapegrout Fast-Set Rapido provides a structural, shrink-compensated, and fibre-reinforced mortar that sets in 30 minutes. It is formulated for the fast restoration of deteriorated concrete structures, edges of beams, pillars, and balconies damaged by reinforcing rod oxidation, as well as rapid repairs to industrial concrete flooring, concrete pipes, and brick pointing.\u003c\/p\u003e\n\n \u003ch3\u003eHigh-build thixotropic performance\u003c\/h3\u003e\n \u003cp\u003eThis pre-blended hydraulic mortar is thixotropic, allowing installers to trowel applications up to 20–25 mm thick on vertical surfaces in a single layer without slumping. The shrinkage-compensated formulation prevents cracking during the rapid drying phase. Once cured, it achieves an R3 structural rating under EN 1504-3, delivering high compressive and flexural strength alongside low capillary water absorption to protect internal steel reinforcement from future corrosion.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e30-minute setting time:\u003c\/strong\u003e Fast initial set allows the mortar to support mechanical loads and light traffic within 2 to 3 hours of application.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e\u0026gt; 40 MPa compressive strength:\u003c\/strong\u003e Meets and exceeds the Class R3 structural requirement (≥ 25 MPa) at 28 days, beginning with a rapid strength gain of \u0026gt; 10 MPa after just 3 hours.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e10-minute pot life (at +20°C):\u003c\/strong\u003e A tight mixing and application window requiring installers to prepare only what can be placed immediately.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e18 kg\/m² per cm consumption rate:\u003c\/strong\u003e Provides a predictable coverage floor for calculating material requirements on deep structural patches or floor repairs.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e\u0026gt; 1.5 MPa bond strength:\u003c\/strong\u003e High-adhesion performance under EN 1542 tests to ensure permanent integration with prepared, damp concrete substrates.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eRestoration of damaged concrete pillars, beams, and balcony edges.\u003c\/li\u003e\n \u003cli\u003eFast repairs to industrial concrete floors requiring quick return to service.\u003c\/li\u003e\n \u003cli\u003eSealing surface cracks in concrete and cement renders.\u003c\/li\u003e\n \u003cli\u003eFast smoothing of surface defects in fresh concrete pours, including aggregate bridging, shrinkage joints, and formwork spacer holes.\u003c\/li\u003e\n \u003cli\u003eAssembly and edge repair of concrete pipes.\u003c\/li\u003e\n \u003cli\u003ePointing between bricks on structures prior to waterproofing with Planiseal 88.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eInstallation and application\u003c\/h3\u003e\n \u003cp\u003eSubstrates must be mechanically prepared to a rough, sound finish with surface irregularities at least 5 mm deep to expose the aggregate. All concrete surfaces must be thoroughly wet with water, allowing excess water to evaporate so the substrate is damp but free of puddles. For optimal adhesion, brush on a bonding slurry composed of 1 part Mapegrout Fast-Set Rapido to 0.24–0.25 parts water immediately before trowelling the mortar mix.\u003c\/p\u003e\n \u003cp\u003eMix a 25 kg bag with 3.75–4 litres of clean water using an electric mixer until smooth. Apply with a float or trowel to the wet slurry. For repairs deeper than 2.5 cm, apply multiple layers at 15-minute intervals, scoring each intermediate layer with a 10 mm notched trowel. Keep restored areas damp for at least 24 hours, or protect floor repairs with polyethylene sheets or wet bags to prevent rapid evaporation.\u003c\/p\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not add extra water to the mix after setting has commenced in an attempt to restore workability.\u003c\/li\u003e\n \u003cli\u003eDo not add cement, lime, gypsum, or any other admixtures to the powder.\u003c\/li\u003e\n \u003cli\u003eDo not apply to dry, dirty, or unprepared surfaces.\u003c\/li\u003e\n \u003cli\u003eDo not use for precision machinery or column anchoring; use Mapefill or Mapefill R instead.\u003c\/li\u003e\n \u003cli\u003eDo not apply with plaster sprayers; use Mapegrout Thixotropic instead.\u003c\/li\u003e\n \u003cli\u003eDo not apply in temperatures below +5°C or above +35°C.\u003c\/li\u003e\n \u003cli\u003eMay undergo colour variation after hardening; it is not recommended for use as an exposed aesthetic façade finish.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Mapei","offers":[{"title":"Default Title","offer_id":46558646829248,"sku":"MAPGROUTRAP\/25","price":82.39,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/MapeiGrout-Rapido-Product-Image.png?v=1754479965"},{"product_id":"mapei-lamposilex","title":"Mapei Lamposilex (Waterplug)","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor stopping active water leaks under pressure in basements, subways, and concrete water tanks, Lamposilex provides an ultra-fast setting plug that halts water flow within minutes. This chloride-free hydraulic binder mixes with water to form a thixotropic paste that hangs on vertical surfaces without formwork, curing rapidly to block cracks, holes, and joints against hydrostatic pressure.\u003c\/p\u003e\n\n \u003ch3\u003eHow it works\u003c\/h3\u003e\n \u003cp\u003eLamposilex relies on a rapid hydration mechanism. When mixed with water, it transitions from a workable, plastic consistency to a rigid, waterproof plug in approximately one and a half minutes at +20°C. Once set, it exhibits high compressive and flexural strength within 30 minutes, ensuring the plug resists the shear forces of pressurized water. Because it contains no chlorides, it will not contribute to the corrosion of steel reinforcement. Additionally, it is certified to AS\/NZS 4020:2018, making it safe for sealing joints and cracks in contact with potable water.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e1.5-minute setting time (at +20°C):\u003c\/strong\u003e The exact physical window to mix, mold, and force the plug into the leaking cavity before hydration makes the material unworkable.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e1-minute pot life:\u003c\/strong\u003e The maximum time available to prepare and place the mix, requiring the user to mix only what can be applied instantly.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e17 N\/mm² compressive strength (at 30 minutes):\u003c\/strong\u003e Fast mechanical development to withstand structural and hydrostatic loads shortly after placement, rising to 46 N\/mm² after 28 days.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e3 N\/mm² flexural strength (at 30 minutes):\u003c\/strong\u003e Early tensile capability to resist cracking under joint movement, rising to 9 N\/mm² after 28 days.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e1.8 kg\/dm³ consumption:\u003c\/strong\u003e The material requirement to calculate coverage, where 1.8 kg of dry powder is needed to fill each litre of cavity volume.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eInstant stopping of active water leaks, including water under pressure.\u003c\/li\u003e\n \u003cli\u003eSealing water leaks in basements, subways, and below-grade concrete structures.\u003c\/li\u003e\n \u003cli\u003eStopping leaks in above-ground potable water tanks.\u003c\/li\u003e\n \u003cli\u003eWaterproof sealing of rigid joints between concrete walls and floor slabs.\u003c\/li\u003e\n \u003cli\u003eWaterproof sealing of structural cracks and holes.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eApplication procedure\u003c\/h3\u003e\n \u003cp\u003eFor sealing active water leaks, enlarge the crack or hole to a minimum of 2 cm wide and 2 cm deep, keeping the inner cavity wider than the exterior opening (dovetail profile) to mechanically lock the cured plug in place. Remove all loose material from the cavity.\u003c\/p\u003e\n \u003cp\u003eFor rigid wall-to-floor joints, remove degraded concrete and clear dust with compressed air. Thoroughly wet the substrate so it is saturated but free of standing surface water before application.\u003c\/p\u003e\n \u003cp\u003eMix 1 kg of powder with 280 g of water (or 2.5 parts powder to 1 part water by volume) using a trowel until smooth. Mold the mix manually into the shape of a cork, wait a few seconds until the curing process begins, then force the plug into the hole. Hold under constant pressure for 2 to 3 minutes until fully set. For rigid joints, work the mix into the cavity immediately after mixing, and keep the surface damp for the first 15 to 20 minutes.\u003c\/p\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not add lime, cement, or gypsum to the mix.\u003c\/li\u003e\n \u003cli\u003eDo not leave drums exposed to direct sunlight before use.\u003c\/li\u003e\n \u003cli\u003eDo not apply at temperatures below +5°C.\u003c\/li\u003e\n \u003cli\u003eIn hot weather, store the product out of the sun and use cold water to prevent premature setting. In cold temperatures, store in a heated room and use water at +20°C to prevent delayed setting.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Mapei","offers":[{"title":"Single Buy","offer_id":46758832439488,"sku":"LAMPOSIL\/5","price":49.53,"currency_code":"AUD","in_stock":true},{"title":"Box Buy (4)","offer_id":46758828146880,"sku":"LAMPOSIL\/5\/BOX","price":178.28,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/mapei-lamposilex.png?v=1757652205"},{"product_id":"rla-penatech-hs-grout","title":"RLA Penatech HS Grout","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eFor structural concrete applications subject to dynamic loads and continuous vibrations, RLA Penatech HS Grout provides a high-strength, precision Class C cementitious grouting system. It is formulated to achieve non-shrink dual expansion, compensating for volume loss in both the plastic and hardened states to maintain full bearing contact under machine base plates, bridge bearing pads, and crane rail sole plates.\u003c\/p\u003e\n\u003ch3\u003eHigh-strength structural performance\u003c\/h3\u003e\n\u003cp\u003ePenatech HS Grout is a chloride-free cementitious system designed for gap depths from 10mm up to 150mm in a single application. The gaseous expansion mechanism begins after 5 minutes and completes within 25 minutes of mixing, offsetting shrinkage before and during the curing phase. It contains non-metallic wire content to eliminate rust staining on exposed concrete faces. When mixed to a flowable consistency, it maintains excellent flow retention to completely fill deep cavities, core holes, and pre-cast concrete panel gaps without bleeding or segregation.\u003c\/p\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompressive strength (Flowable):\u003c\/strong\u003e Reaches \u0026gt;25 MPa at 1 day, \u0026gt;50 MPa at 7 days, and \u0026gt;65 MPa at 28 days (tested to AS1012.9-AS2350.11) to support heavy structural loads.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompressive strength (Trowellable):\u003c\/strong\u003e Reaches \u0026gt;35 MPa at 1 day, \u0026gt;75 MPa at 7 days, and \u0026gt;85 MPa at 28 days for applications requiring rapid early strength.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual expansion window:\u003c\/strong\u003e Expansion starts at 5 minutes and finishes at 25 minutes to ensure early volume stability while the grout is still plastic.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eZero bleed (0%):\u003c\/strong\u003e Prevents water accumulation and top-edge gaps under critical base plates when mixed within specified water ratios.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVariable water ratios per 20kg bag:\u003c\/strong\u003e 2.2–2.6 litres for dry-pack\/stiff grout, 2.8–3.2 litres for plastic\/trowellable grout, and 3.5–4.0 litres for flowable\/pourable grout.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhere to use it\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMachine base plates requiring critical, void-free support.\u003c\/li\u003e\n\u003cli\u003eHigh-performance structural grouting under bridge bearing pads and crane rail sole plates.\u003c\/li\u003e\n\u003cli\u003eAnchor bolt fillings and core hole grouting.\u003c\/li\u003e\n\u003cli\u003ePre-cast concrete sections, panels, cavities, gaps, and base infills.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eLimitations\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eApplication temperature range:\u003c\/strong\u003e Do not apply in ambient temperatures below 5°C or above 30°C.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCold weather limits:\u003c\/strong\u003e Below 10°C, setting times are extended, early strength gain is dramatically reduced, and some bleeding may occur. Condition the powder and mixing water to 20°C–25°C overnight before use to assist strength development.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHot weather limits:\u003c\/strong\u003e Above 30°C, setting times are accelerated and placement becomes difficult. Keep powder cool, use cold mixing water, and place the grout early in the morning or late in the evening out of direct sunlight.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUnrestrained areas:\u003c\/strong\u003e Keep unrestrained grout areas to a strict minimum to prevent cracking.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWater additions:\u003c\/strong\u003e Do not add water beyond the specified ratios. Excess water causes segregation and bleeding. Discard any grout that has stiffened or become unworkable. Do not mix by hand.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSubstrate restriction:\u003c\/strong\u003e Never apply mixed grout to a dry, porous concrete substrate.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eApplication and installation\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eSubstrate preparation:\u003c\/strong\u003e Concrete substrates must be clean, sound, and free of dust, oil, grease, curing compounds, and contaminants. Bolt holes and anchor points must be completely free of water. All prepared concrete areas must be saturated with clean water for 4 hours before grouting to control porosity. Remove all excess water, puddles, and standing water from holes immediately before placement.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFormwork:\u003c\/strong\u003e Formwork must be leakproof and watertight. Seal the base of the formwork using foam rubber strips, polyurethane, or silicone. Construct the formwork to maintain a grout head on the pour side above the level of the underside of the base plate to facilitate gravity flow. Coat the forms with a release agent or form oil before pouring.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePlacement:\u003c\/strong\u003e Pour mixed flowable grout continuously from one side using a header box to maintain head pressure and prevent air entrapment. For large-volume pumping, use a positive displacement pump and a forced-action mixer. Pump from the bottom upwards to fill voids completely. Ensure bleed or venting holes are present in the formwork or base plate to prevent pressure build-up.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCuring:\u003c\/strong\u003e Cure all exposed grout immediately after application. Cover with plastic sheeting, wet hessian, or apply a wet liquid curing compound from the RLA Curecon range to ensure full strength development.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"RLA","offers":[{"title":"Default Title","offer_id":46872671420608,"sku":"GROUTAFTEKHS\/20","price":53.15,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/aftekPenatechHS.png?v=1759446312"},{"product_id":"ardex-ra-142-structural-crack-injection-epoxy","title":"Ardex RA 142 Structural Crack Injection Epoxy","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor pressure injection and gravity feed structural crack repair in horizontal concrete and masonry, ARDEX RA 142 seals and bonds hairline to fine cracks from 0.05mm to 3mm. This two-component, 100% solids epoxy adhesive has a super low viscosity that penetrates deep into fine fractures to restore structural integrity to interior and exterior slabs, walls, and timber members.\u003c\/p\u003e\n\n \u003ch3\u003eWhat it does\u003c\/h3\u003e\n \u003cp\u003eARDEX RA 142 functions as a high-strength structural binder and adhesive. Its super low viscosity of 190 cps allows it to flow freely into narrow fissures where thicker epoxies cannot penetrate. When mixed with kiln-dried sand or aggregate, it serves as a high-strength epoxy resin mortar for concrete spall repairs and interior surface overlays. The solvent-free formulation cures to a highly rigid polymer, achieving a compressive strength of 70 MPa and a tensile strength of 50 MPa to reinstate load path continuity across sheared or fractured structural sections.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e0.05mm to 3mm crack width:\u003c\/strong\u003e The target application window for horizontal and vertical concrete crack injection; for wider cracks, use ARDEX RA 144.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e190 cps mixed viscosity:\u003c\/strong\u003e A highly fluid, very thin liquid consistency that ensures deep penetration into tight hairline fractures.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e70 MPa compressive strength (7 days):\u003c\/strong\u003e Delivers structural loading capacity well exceeding standard concrete strengths.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e20-minute gel time (+24°C):\u003c\/strong\u003e The working window to dispense and inject the material before the chemical reaction begins to thicken the epoxy.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e24-hour full cure:\u003c\/strong\u003e The required setting window before injection ports, tubing, and capping paste can be chipped or ground off the substrate.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cp\u003eThis structural epoxy is suitable for repairing dormant cracks in several configurations:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eHorizontal concrete slabs:\u003c\/strong\u003e Gravity-fed directly into prepared, grooved cracks or used for shear fracture repairs in both interior and exterior slabs.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eVertical concrete and masonry walls:\u003c\/strong\u003e Pressure-injected through fixed ports in conjunction with a surface capping paste such as ARDEX RA 88.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eSpall repairs and patches:\u003c\/strong\u003e Mixed at a 2:1 ratio by volume with 4 to 5 parts of kiln-dried sand to form a pourable, trowelable repair mortar.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eConcrete bonding:\u003c\/strong\u003e Applied by brush or roller to bond fresh concrete to hardened concrete, or to bond hardened concrete sections together.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eTimber members:\u003c\/strong\u003e Structural crack injection repairs for dormant cracks in wood structures.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not use to repair active cracks subject to ongoing movement; the cause of the cracking must be resolved prior to application.\u003c\/li\u003e\n \u003cli\u003eDo not use to stop seeping or flowing water; the crack must be dry at the time of injection for proper bonding.\u003c\/li\u003e\n \u003cli\u003eDo not thin with solvents, as this will prevent the epoxy from curing.\u003c\/li\u003e\n \u003cli\u003eNew concrete substrates must be a minimum of 28 days old before application.\u003c\/li\u003e\n \u003cli\u003eDo not use for basement walls where the back side of the concrete is inaccessible and runoff cannot be monitored; use the higher viscosity, thixotropic ARDEX RA 146 gel instead.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eHow to apply\u003c\/h3\u003e\n \u003cp\u003eFor gravity-feed crack repairs, cut a groove 3mm wide and at least 1mm deep along the crack using an abrasive or diamond blade. Wire brush the groove and blow out all dust, dirt, grease, and contaminants prior to pouring or injecting the epoxy.\u003c\/p\u003e\n \u003cp\u003eFor spall repairs, cut a clean vertical edge around the spall perimeter to a minimum depth of 20mm to prevent feathered edges. Chip out loose material, clean the cavity, and mix Part A and Part B at a 2:1 ratio by volume before mixing in aggregate. Apply at a maximum mortar thickness of 35mm per coat.\u003c\/p\u003e\n \u003cp\u003eFor vertical cracks, clean the surface, secure injection ports at 15cm to 30cm intervals using ARDEX RA 88 capping paste, and seal the entire crack face. Inject ARDEX RA 142 from the lowest port upward until material flows from the adjacent port. Keep the final port under pressure for 30 seconds to ensure complete filling.\u003c\/p\u003e\n\n \u003ch3\u003eCartridge setup and dispensing\u003c\/h3\u003e\n \u003cp\u003eKeep the dual cartridge upright during preparation to prevent leakage. Shake the cartridge for 1 minute, then stand it upright for 1 minute to allow air bubbles to rise. Load it into the dispenser and point it upward at a 45-degree angle. Remove the cap and plug, then dispense material into a waste container until both parts flow evenly. Insert the flow control port and nozzle, point upward at 45 degrees, and dispense 1 to 2 trigger pulls to prime the nozzle. If using a pneumatic dispenser, use an air pressure regulator limited to a maximum of 275 kPa (40 psi) to prevent plunger leakage.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Ardex","offers":[{"title":"Default Title","offer_id":46922357866688,"sku":"INJARDRA142","price":143.22,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/Ardex-RA-142.png?v=1759892271"},{"product_id":"ardex-ra-88-plus-multi-purpose-epoxy-repair-adhesive","title":"Ardex RA 88 Plus Multi-Purpose Epoxy Repair Adhesive","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor horizontal, vertical, and overhead concrete repairs, ARDEX RA 88 Plus is a non-drip, non-sag epoxy adhesive that fills holes, seals cracks, and sets anchor bolts. It is formulated to bond structurally to major construction substrates—including metal, concrete, brick, wood, stone, and block—and meets AS\/NZS 4020 for contact with potable drinking water.\u003c\/p\u003e\n\n \u003ch3\u003eWhat it does\u003c\/h3\u003e\n \u003cp\u003eARDEX RA 88 Plus is a two-component epoxy that cures to a high compressive strength of 87 MPa, making it suitable for structural repairs and spall patching. Its paste consistency allows it to be trowelled flush into overhead or vertical gaps without running or sagging. The adhesive serves as a chemical anchor for bolts, a rigid seal for crack injection ports, and a high-strength termination sealant for selected ARDEX Sheet Applied Waterproofing Membranes inside prepared reglets. In swimming pools, its density allows underwater installation of tiles on side walls or bottom surfaces when applied to a dry tile.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e87 MPa compressive strength (ASTM D695):\u003c\/strong\u003e High-load resistance for structural concrete patching and anchor bolt installations after a 7-day cure.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e20.1 MPa bond strength (ASTM C882):\u003c\/strong\u003e High-strength adhesion when bonding hardened concrete to hardened concrete after 14 days.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e3-hour tack-free cure (at 24°C):\u003c\/strong\u003e Rapid curing window that allows the epoxy to be ground mechanically, painted, or opened to full traffic after 3 hours.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e45-minute working time (at 24°C):\u003c\/strong\u003e Practical wet-edge window to align tiles, secure injection ports, or trowel spalls flush before curing begins. Working time drops to 20 minutes at 40°C and extends to 90 minutes at 4°C.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e0.00015% shrinkage (ASTM D2566):\u003c\/strong\u003e Negligible shrinkage at 48 hours, preventing tension cracks or bond-line failures along concrete joints.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eWaterproofing terminations:\u003c\/strong\u003e Sealing reglets and fixing Over-Flashing details for selected ARDEX Sheet Applied Waterproofing Membranes.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eConcrete spall repairs:\u003c\/strong\u003e Patching ground-down spalls between 13mm and 16mm deep, and up to 76mm wide.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eCrack injection:\u003c\/strong\u003e Adhering injection ports and sealing the face of cracks prior to injecting epoxy repair resins.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eRigid bonding:\u003c\/strong\u003e Structural bonding of metal, brick, stone, block, wood, and concrete.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003ePool maintenance:\u003c\/strong\u003e Replacing dislodged tiles underwater along pool walls and floors.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not use ARDEX RA 88 Plus to repair cracks subject to movement.\u003c\/li\u003e\n \u003cli\u003eDesigned for small patch repairs only. Deep or large-mass repairs will generate excessive chemical reaction heat, which can cause swelling, smoking, and cracking.\u003c\/li\u003e\n \u003cli\u003eDo not thin the product with solvents, as this will prevent curing.\u003c\/li\u003e\n \u003cli\u003eNot recommended for vertical crack or spall repairs underwater; underwater use is restricted to replacing tiles.\u003c\/li\u003e\n \u003cli\u003eThe cured epoxy may discolour under UV exposure.\u003c\/li\u003e\n \u003cli\u003eIf overcoating with paints or architectural coatings, avoid solvent-based coatings. Sanding the cured surface first is required to aid coating adhesion.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eHow to apply\u003c\/h3\u003e\n \u003cp\u003eEnsure concrete substrates are a minimum of 28 days old. All concrete surfaces must be clean and mechanically prepared by rough-grinding, scarifying, or bush hammering to achieve a roughened profile. Smooth surfaces like wood or metal must be mechanically roughened with a wire brush or sandpaper. All dust, dirt, oil, and contaminants must be removed by vacuuming prior to application.\u003c\/p\u003e\n \u003cp\u003eTo prepare the cartridge, unscrew the plastic cap, remove the plug, and load the cartridge into an ARDEX Heavy Duty Caulking Gun (use the 254ml gun for the 254ml size, or the dual-cartridge gun for the 627ml size). Dispense a small amount of material until both parts flow evenly. Attach the mixing nozzle and purge a small amount of product until the paste has a consistent grey colour with no streaks.\u003c\/p\u003e\n \u003cp\u003eSubstrate and ambient air temperatures must be between 5°C and 35°C. If the work site or substrate is below 21°C, condition the cartridges to 21°C–24°C before use to prevent the product from thickening. Clean tools immediately with a mild solvent; cured epoxy can only be removed mechanically. The adhesive must be fully cured before conducting any water flood testing on waterproofing membranes.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Ardex","offers":[{"title":"Default Title","offer_id":46922474913984,"sku":"INJARDRA88","price":143.73,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/Ardex-RA-88.png?v=1759893504"},{"product_id":"gripset-b26","title":"Gripset B26 Asphalt Crack Filler","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor sealing cracks in asphalt and bitumen surfaces without the safety risks and equipment setup of hot-pour bitumen, Gripset B26 Asphalt Crack Filler provides a cold-applied, fast-drying alternative. The pourable liquid fills horizontal gaps and road cracks to block water ingress, drying to a flexible, non-tacky black film that accepts vehicular traffic in approximately 15 minutes.\u003c\/p\u003e\n\n \u003ch3\u003eHow it works\u003c\/h3\u003e\n \u003cp\u003eGripset B26 is a solvent-free bitumen compound formulated to penetrate to the full depth of asphalt cracks. As a cold-applied liquid, it does not require heating or specialised melting kettles on site. Once poured, the compound bridges the gap and cures to a flexible barrier with 300% elongation, allowing the joint to accommodate the natural thermal movement of asphalt roads and pavements without cracking or losing adhesion. Its water-resistant formulation also resists ground salts, sulphates, and diluted acids, preventing sub-base damage from chemical and water runoff.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e15-minute traffic window:\u003c\/strong\u003e Fast-drying properties allow roads and driveways to be reopened to vehicles approximately 15 minutes after application.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e300% elongation (AS1145-1989):\u003c\/strong\u003e High elasticity prevents the cured seal from tearing as asphalt expands and contracts under solar heating and overnight cooling.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e80 metres per litre coverage:\u003c\/strong\u003e A single litre covers approximately 80 linear metres of a standard 2mm wide by 5mm deep asphalt crack.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e0.35MPa tensile strength (AS1145-1989):\u003c\/strong\u003e Maintains cohesive strength across sealed joints under civil and commercial traffic loads.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e50 Shore A hardness (ASTM D2240-97):\u003c\/strong\u003e Provides a balanced, resilient hardness to resist stone embedment while remaining flexible.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eAsphalt road crack sealing and pavement maintenance.\u003c\/li\u003e\n \u003cli\u003eHorizontal bitumen joints and gaps on commercial, industrial, and civil sites.\u003c\/li\u003e\n \u003cli\u003eWaterproof sealing between old and new asphalt layers during road repairs.\u003c\/li\u003e\n \u003cli\u003ePourable joint filling on stable, non-moving asphalt and bitumen surfaces.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eApplication guide\u003c\/h3\u003e\n \u003cp\u003eBefore application, blow, vacuum, or sweep the crack to remove all loose dirt, dust, aggregate, and weeds. The crack must be clean, free from rising damp, and wider than 2mm to ensure the liquid can penetrate. While Gripset B26 can be applied over damp surfaces, any standing water or dew should be cleared; during cooler periods, a naked flame from a propane torch can be used to dry and pre-heat the crack.\u003c\/p\u003e\n \u003cp\u003eStir the product with a manual stirrer or drill paddle until it reaches a fluid, homogenous consistency, then decant into a spray unit or spout pouring device with a minimum 5mm opening. Pour the material directly into the crack, leaving it slightly \"proud\" of the surface. Because the formula is designed to sink deep into the crack, inspect the run after a few minutes for voids where the material has settled, and reapply as needed to ensure a full-depth seal.\u003c\/p\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not apply to expansion joints or movement joints.\u003c\/li\u003e\n \u003cli\u003eDo not use in areas subject to petroleum, fuel, or solvent spills.\u003c\/li\u003e\n \u003cli\u003eDo not apply when the surface temperature is below 5°C or above 35°C.\u003c\/li\u003e\n \u003cli\u003eDo not apply if rain is imminent or forecast within 24 hours of application.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Gripset","offers":[{"title":"Default Title","offer_id":46933862875328,"sku":"GRIPB26\/15","price":187.64,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/gripsetb26.png?v=1760075661"},{"product_id":"rla-penatech-hes-grout","title":"RLA Penatech HES Grout","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor civil engineering and heavy infrastructure installations where equipment downtime must be minimised, RLA \u003ca href=\"\/products\/rla-penatech-gp-grout\"\u003ePenatech\u003c\/a\u003e HES Grout provides rapid strength development on concrete substrates. Tested and compliant with AS1012 and AS1478 as a Class C grout, this dual-expansion, shrinkage-compensated formula allows structural loads, crane rail plates, bridge bearing pads, and heavy machinery base plates to be fully reinstated in 24 hours.\u003c\/p\u003e\n\n \u003ch3\u003eDual-stage shrinkage compensation\u003c\/h3\u003e\n \u003cp\u003ePenatech HES Grout utilises a blend of Portland cement, graded fillers, and chemical additives to control expansion across both the plastic and hardened states. In the plastic state, it expands by 1% to 2% within the first 5 to 25 minutes of mixing to counteract early settlement. It continues to expand during hardening, compensating for long-term drying shrinkage to maintain complete contact under high-load base plates and within precast joints. The non-metallic formulation is iron-free, preventing rust staining in exposed exterior applications.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e2-hour compressive strength (\u0026gt;35 MPa Flow \/ \u0026gt;25 MPa Fluid):\u003c\/strong\u003e Rapid early strength development to support structural loads and facilitate fast equipment reinstatement.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e28-day compressive strength (\u0026gt;85 MPa Flow \/ \u0026gt;65 MPa Fluid):\u003c\/strong\u003e Tested to AS1012.9 and AS1478.2, ensuring high ultimate load-bearing capacity under dynamic forces and continuous vibration.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e10mm to 120mm application thickness:\u003c\/strong\u003e Suitable for single-pour under-plate grouting and bolt-hole anchoring without aggregate addition.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e10-minute placement window:\u003c\/strong\u003e At 20°C, the mixed grout must be placed within 10 minutes to secure the full benefit of the plastic expansion process.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e2.0 kg\/m²\/mm coverage:\u003c\/strong\u003e Highly predictable material planning for calculating consumption in cavities, gaps, and recesses.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eHeavy-duty support under high-load machine base plates.\u003c\/li\u003e\n \u003cli\u003eGrouting crane rail plates and bridge bearing pads subject to dynamic loads and continuous vibration.\u003c\/li\u003e\n \u003cli\u003ePrecast concrete panel grouting and structural connection cavities.\u003c\/li\u003e\n \u003cli\u003eAnchoring bolts, dowels, and fixing pockets in solid concrete.\u003c\/li\u003e\n \u003cli\u003eFilling concrete cavities, gaps, and structural recesses.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eInstallation and mixing limits\u003c\/h3\u003e\n \u003cp\u003eFor quantities up to 40kg, a slow-speed drill fitted with a high-shear mixer must be used. Larger quantities require a high-shear vane mixer. Do not use a colloidal impeller mixer. Add the powder slowly to pre-measured clean water and mix continuously for 5 minutes to achieve a smooth, even consistency.\u003c\/p\u003e\n \u003cp\u003eWater requirements per 20kg bag:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eFlow consistency:\u003c\/strong\u003e 2.5 to 2.8 litres of water (Yields 10.3 litres per bag; 97 bags required per cubic metre).\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eFluid consistency:\u003c\/strong\u003e 3.2 to 3.5 litres of water (Yields 11.0 litres per bag; 91 bags required per cubic metre).\u003c\/li\u003e\n \u003c\/ul\u003e\n \u003cp\u003eClean concrete substrates thoroughly to remove oil, grease, and laitance by scabbling or water blasting. Flood the foundation area with fresh water for several hours to pre-soak, removing all free standing water from bolt holes and pockets immediately before pouring. Grout must be poured continuously from one side of the void to prevent air entrapment. Always grout bolt pockets before grouting the main gap beneath the base plate.\u003c\/p\u003e\n \u003cp\u003eFor pours thicker than 120mm, Penatech HES Grout must be filled out with a well-graded, silt-free aggregate, such as Epilox Fillers F4 added at 10kg per 20kg bag, to control heat build-up. Note that adding aggregate creates a heat sink that will slightly retard the grout set and slow early strength development during the first few hours.\u003c\/p\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eLow-temperature working:\u003c\/strong\u003e When ambient or contact surface temperatures are 5°C or below on a falling thermometer, warm water (30°C to 40°C) is required for mixing to accelerate strength development. For temperatures below 10°C, formwork must remain in place for at least 36 hours.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eHigh-temperature working:\u003c\/strong\u003e When ambient temperatures exceed 35°C, cool water (below 20°C) must be used to mix the grout. Keep unmixed bags stored undercover and as cool as possible.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eUnrestrained surfaces:\u003c\/strong\u003e Keep unrestrained grout surface area to a minimum. Maintain a gap of 150mm on the pouring side and 50mm on the opposite side, with no gap at the flank sides of the plate.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"RLA","offers":[{"title":"Default Title","offer_id":46967580098752,"sku":"GROUTPENATECH\/HES20","price":70.86,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/RLA-HES-GROUT.png?v=1760930500"},{"product_id":"gripset-b09","title":"Gripset B09 Bituminous Surface Treatment","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor rejuvenating oxidised asphalt and resurfacing pitted asphalt layers on airfields, residential streets, car parks, driveways, and sports surfaces, Gripset B09 restores the binder content in the asphalt layer to protect the surface against weather degradation.\u003c\/p\u003e\n\n \u003ch3\u003eHow it works\u003c\/h3\u003e\n \u003cp\u003eGripset B09 is a cold-applied bituminous surface treatment formulated with polymer technology to provide a modified bitumen coating with high adhesion and impact resistance. The cured film is non-slip, non-tacky, and resists sulphates, ground salts, and diluted acids. It features a cross-linking property with Portland cement; adding a cement slurry to the mix accelerates drying times, allows application over damp surfaces, and provides rapid water ponding resistance when rain is imminent.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e 1 litre per 2m² on standard surfaces. A two-coat application is required for optimum durability.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eDrying times (at 23°C and 50% RH):\u003c\/strong\u003e Tack-free in 20 minutes, recoat in 30 minutes, weatherproof film in 4 to 6 hours, and ready for vehicle or pedestrian traffic in 24 hours. These times improve when cement is added.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eSolid content:\u003c\/strong\u003e 68% for high-build film thickness that resists cracking, flaking, and chipping under impact.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003ePot life with cement:\u003c\/strong\u003e 4 hours. Once the cement slurry is incorporated, the mixture must be used within this window.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eRejuvenating oxidised asphalt on secondary roads, residential streets, and car parks.\u003c\/li\u003e\n \u003cli\u003eResurfacing pitted asphalt layers on airfields, bicycle paths, footpaths, and laneways.\u003c\/li\u003e\n \u003cli\u003eRestoring asphalt driveway surfaces and repairing existing asphalt sport surfaces.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eNot designed for major road re-surfacing.\u003c\/li\u003e\n \u003cli\u003eDo not apply when the surface temperature is below 5°C or above 35°C.\u003c\/li\u003e\n \u003cli\u003eDo not use in areas subject to heavy or continuous solvent or petroleum spillage.\u003c\/li\u003e\n \u003cli\u003eDo not use in areas subject to negative hydrostatic pressure.\u003c\/li\u003e\n \u003cli\u003eDo not use as a waterproof membrane.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eApplication and mixing\u003c\/h3\u003e\n \u003cp\u003ePrepare all asphalt substrates thoroughly to ensure they are structurally sound, stable, dry (unless incorporating cement), and clean. Repair pavement surface cracks using the \u003ca href=\"\/products\/gripset-b26\"\u003eGripset B26\u003c\/a\u003e Crack Repair method, and address structural defects with Gripset Patch-phalt repair compound. Clean oil, grease, or wax residues using proprietary degreasers and pressure washing. Remove algae or moss with organic growth removal compounds before application.\u003c\/p\u003e\n \u003cp\u003eStir Gripset B09 before use. Apply using a spray unit, manual squeegee, or self-propelled mechanical squeegee. For applications in cool conditions or when rain is expected within 4 hours, mix 750ml of wet cement slurry (Portland cement powder and water) per 15-litre pail of Gripset B09. Stir at medium speed with a drill and paddle mixer until evenly dispersed.\u003c\/p\u003e\n\n \u003ch3\u003eSystem components\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eGripset Patch-phalt:\u003c\/strong\u003e For repairing deep pavement defects before coating.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eGripset B26:\u003c\/strong\u003e For treating existing cracks in the asphalt substrate prior to surface treatment.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Gripset","offers":[{"title":"Default Title","offer_id":47039291916480,"sku":"GRIPB09\/15","price":191.42,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/GripsetB09.png?v=1762749070"},{"product_id":"ardex-ra-54","title":"Ardex RA 54 Joint Sealant","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor industrial concrete floors subject to heavy-duty vehicle traffic, ARDEX RA 54 fills interior control joints and new construction saw joints to support heavy wheels and prevent joint edge spalling. This fast-setting, semi-rigid polyurea formulation cures rapidly, allowing repaired joints to be shaved in 45 minutes and opened to full traffic in 90 minutes at 23°C.\u003c\/p\u003e\n\n \u003ch3\u003eWhat it does\u003c\/h3\u003e\n \u003cp\u003eARDEX RA 54 is a semi-rigid joint sealant designed to protect concrete joint edges from chipping under the impact of heavy warehouse and industrial traffic. With a Shore A hardness of 75 to 80, it provides the necessary rigidity to support wheel loads across the joint while maintaining 10% to 12% joint movement to accommodate minor thermal cycling. The material feeds by gravity into prepared joints, can be overfilled, and is shaved flush with the floor surface using a sharp floor scraper after curing.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e90-minute cure time:\u003c\/strong\u003e Rapid return-to-service window at 24°C, minimizing facility downtime by allowing vehicle traffic shortly after application.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e75 - 80 Shore A hardness:\u003c\/strong\u003e High semi-rigid support to reinforce concrete joint shoulders against heavy-duty wheel loads.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e8.3 MPa tensile strength:\u003c\/strong\u003e High cohesive strength to maintain joint integrity under stress.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e45-minute shave window (at 23°C):\u003c\/strong\u003e Practical timing for installers to scrape excess overfilled material flush with the concrete surface. This window varies by temperature: 20 minutes at 38°C to 49°C, 45 minutes at 21°C to 27°C, and up to 2 hours at 10°C to 15°C.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e0 g\/L VOC:\u003c\/strong\u003e Clean formulation suitable for interior industrial installations without solvent emissions.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cp\u003eSuitable for horizontal concrete surfaces, including interior control joints, new construction saw joints, and cured cracks. It can be used in exterior applications only when joint movement from thermal cycling remains minimal (10% to 12%). For heavy-duty traffic areas, joint width must be a maximum of 19mm with a minimum depth of three times the width, or 60mm. For light foot traffic, the joint width must be a maximum of 19mm with a minimum depth of 13mm.\u003c\/p\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not use in expansion joints; ARDEX RA 54 is not designed for joints subject to high movement.\u003c\/li\u003e\n \u003cli\u003eHighly sensitive to moisture during application and cure. Do not apply if any dampness or moisture is present in the substrate or environment.\u003c\/li\u003e\n \u003cli\u003eNew concrete must be fully cured for a minimum of 28 days to release moisture before application.\u003c\/li\u003e\n \u003cli\u003eIn exterior applications, the grey material will initially change colour to grey-green before returning to grey after 90 days.\u003c\/li\u003e\n \u003cli\u003eDo not attempt to force adhesive out of a hardened mixing nozzle; always use a new nozzle with each new cartridge to avoid cartridge rupture or improper mixing.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eHow to apply\u003c\/h3\u003e\n \u003cp\u003eEnsure the concrete bonding surfaces are clean, sound, and dry. Old concrete must be profiled or mechanically roughened with a wire brush or sandpaper, while new concrete must be at least 28 days old. Cut along cracks using a saw or grinder with a dry diamond or abrasive blade to create a clean 90° angle, preventing feathered edges. Blow out all dust and debris from the joint.\u003c\/p\u003e\n \u003cp\u003eInsert a backer rod or clean kiln-dried sand into the bottom of the joint prior to dispensing. This prevents three-sided adhesion (bonding to the bottom), which causes sealant failure during joint expansion and contraction. Dispense the polyurea using steady, full trigger pulls to gravity-feed the joint, slightly overfilling if the joint is to be shaved flush.\u003c\/p\u003e\n\n \u003ch3\u003eTopcoat compatibility\u003c\/h3\u003e\n \u003cp\u003eIf applying a topcoat over ARDEX RA 54, wait 24 hours after application before applying a primer. A premium primer must be applied before any topcoat is laid down. Always install a small test area of the primer and topcoat system and observe it for 7 days to verify adhesion and compatibility before proceeding with the full application.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Ardex","offers":[{"title":"Box Buy (12)","offer_id":47061258502336,"sku":"ARDRA54\/CTG\/BOX","price":1014.48,"currency_code":"AUD","in_stock":true},{"title":"Single","offer_id":47061258535104,"sku":"ARDRA54\/CTG","price":93.93,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/Ardex-54.png?v=1763336297"},{"product_id":"rla-uw-penaflow-grout","title":"RLA UW Penaflow Grout","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eFor structural grouting underneath precast concrete panels, filling core holes, and securing anchor bolts, UW Penaflow Grout is a Class A non-shrink cementitious grout that controls settlement using a gaseous expansion system. It is formulated to eliminate shrinkage while in a plastic state, ensuring complete contact and load transfer between concrete substrates and base plates.\u003c\/p\u003e\n\u003ch3\u003eHow it works\u003c\/h3\u003e\n\u003cp\u003eUW Penaflow Grout uses a pre-blended mix of Portland cement, graded aggregates, and chemical additives that trigger a 1% to 2% volumetric expansion while the mix is still plastic. This expansion begins 15 minutes after mixing and finishes within 3 hours, pushing the grout into close contact with unrestrained surfaces before curing begins. The formula contains no metallic iron, preventing rust staining on exposed concrete panel edges and joint lines.\u003c\/p\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e20mm to 150mm application thickness:\u003c\/strong\u003e Allows single-pass pours underneath precast sections and inside deep cavities without the risk of thermal cracking.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e55 MPa compressive strength (at 28 days):\u003c\/strong\u003e Provides high load-bearing capacity for underpinning and structural base infills (tested to AS1012.9 and AS2073).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e10 MPa bond strength (at 28 days):\u003c\/strong\u003e Ensures high-strength adhesion to structural concrete surfaces, measured via the ASTM C882-1987 Slant Shear Method.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAdjustable consistency yields:\u003c\/strong\u003e A 20kg bag yields 10.3 litres as a dry pack, 10.6 litres when trowellable, and 11.0 litres when mixed to a flowable consistency.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhere to use it\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eGrouting underneath precast concrete panels and structural concrete sections.\u003c\/li\u003e\n\u003cli\u003eFilling core holes created in panels by core drilling.\u003c\/li\u003e\n\u003cli\u003eSecuring anchor bolts and filling structural cavities, gaps, and base infills.\u003c\/li\u003e\n\u003cli\u003eCore filling in block work and structural underpinning.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eLimitations\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDo not mix by hand:\u003c\/strong\u003e Must be mixed using a mechanical forced-action mixer, high shear mixer, or a drill with a spiral mixing paddle at 500-600 rpm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStrict water limits:\u003c\/strong\u003e Do not add water beyond the specified ratios (maximum 2.9L for dry pack, 3.4L for trowellable, and 4.0L per 20kg bag for flowable). Excess water causes segregation, bleeding, and loss of strength.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDo not vibrate:\u003c\/strong\u003e Mechanical vibration must not be used to assist flow; rely on gravity flow with a header box or a positive displacement pump.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTemperature limits:\u003c\/strong\u003e Only apply when substrate and ambient temperatures are between 10°C and 30°C. Cold temperatures extend setting and strength development times; high temperatures accelerate setting and may cause cracking.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSubstrate condition:\u003c\/strong\u003e Never apply mixed grout to a dry porous substance; the concrete must be pre-soaked with water for 4 hours before application.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003cp\u003eSaturate the concrete substrate with clean water for 4 hours before grouting to reduce porosity and prevent water loss from the mix. Remove all excess water, puddles, and standing water from bolt holes and cavities prior to pouring.\u003c\/p\u003e\n\u003cp\u003eFormwork must be constructed to be completely watertight. Seal the base of the formwork using foam rubber strips or a polyurethane or silicone sealant. Build the formwork to maintain a grout head on the pouring side, allowing continuous gravity flow beneath the base plate to prevent air entrapment.\u003c\/p\u003e\n\u003cp\u003eAlways add the grout powder to pre-measured cold water. Mix mechanically for 3 to 5 minutes until a homogeneous consistency is reached. Discard any mix that has begun to stiffen or has become unworkable.\u003c\/p\u003e\n\u003cp\u003eOnce placed, protect all exposed grout surfaces immediately by covering them with plastic sheeting, wet hessian, or a liquid curing compound such as the Curecon range.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"RLA","offers":[{"title":"Default Title","offer_id":47134041604288,"sku":"GROUTAFTEKUW\/20","price":71.94,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/penaflow-uw-grout-washout-resistant-underwater-adheseal.png?v=1775470247"},{"product_id":"mapei-planicrete-sp","title":"Mapei Planicrete SP","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eMapei Planicrete SP is a white, fluid SBR latex admixture for cement-based screeds, renders, thin smoothing layers and highly adhesive cement bonding slurries. Use it where the mix needs better adhesion, plasticity, thixotropy, water retention and workability.\u003c\/p\u003e\n\u003ch3\u003eWhat it does\u003c\/h3\u003e\n\u003cp\u003eAdded to cement and aggregate mixes, Planicrete improves adhesion to the substrate and, after setting and hardening, increases compressive and flexural strength, abrasion resistance, impermeability and resistance to freeze-thaw cycles.\u003c\/p\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eApplication temperature: +5°C to +40°C.\u003c\/strong\u003e Do not use Planicrete-modified mixes outside this ambient range.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBonded screeds: 10 to 35 mm.\u003c\/strong\u003e Use aggregate no larger than 1\/3–1\/4 of the screed thickness, with an 8 mm maximum.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFloating screeds: over 35 mm.\u003c\/strong\u003e The recommended dilution is 1:4 Planicrete to water, with at least two weeks curing under normal temperature and humidity.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompressive strength to EN 12190:\u003c\/strong\u003e 7 MPa after 1 day, 25 MPa after 7 days and 33 MPa after 28 days for the TDS reference mortar.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAdhesion to EN 1542:\u003c\/strong\u003e more than 2.0 MPa after 28 days at +21°C and 50% U.R. for the TDS reference mortar.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePrepare and mix\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eUse a solid, compact and clean substrate. Remove loose material, dust, concrete crusts, oil, form-release agents and paint.\u003c\/li\u003e\n\u003cli\u003eThoroughly wet the substrate, but leave no excess water on the surface.\u003c\/li\u003e\n\u003cli\u003eDilute Planicrete with water at the ratio specified for the application, then add cement and aggregates. Mix for 2–3 minutes until smooth and even.\u003c\/li\u003e\n\u003cli\u003eFor bonded screeds, apply a Planicrete and cement slurry first, then place the screed fresh-on-fresh before the slurry dries.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eLimitations\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDo not use Planicrete neat as a primer or slurry. Always mix it with Portland cement or, where specified, Mapecem or Topcem.\u003c\/li\u003e\n\u003cli\u003eDo not mix for more than 3 minutes in a concrete mixer, to avoid excessive air entrainment.\u003c\/li\u003e\n\u003cli\u003eIn warm or windy conditions, protect the surface from rapid drying and cure carefully to reduce plastic-shrinkage cracking.\u003c\/li\u003e\n\u003cli\u003eReduce the Planicrete-to-water dilution when aggregates are damp or wet.\u003c\/li\u003e\n\u003cli\u003eResistance to solvents and oils is rated mediocre; resistance to acids and alkalis is rated fair.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Mapei","offers":[{"title":"Default Title","offer_id":47996867182784,"sku":"MAPEPLANI\/25","price":144.73,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/mapei-planicrete-sp-high-bond-tile-adhesive-adheseal.png?v=1775470395"},{"product_id":"mountain-grout-ultra","title":"Mountain Grout Ultra","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eMountain Grout Ultra is a moderate-viscosity hydrophobic polyurethane formulation for sealing leaking cracks and joints where some movement is possible. When injected into wet cracks, it reacts with water to produce a closed-cell foam.\u003c\/p\u003e\n\u003ch3\u003eWhat it does\u003c\/h3\u003e\n\u003cp\u003eUltra is used in water-related structures to form an inert, non-toxic permanent seal. Its cured elongation of 300% suits leaking cracks or joints where movement may occur, while the hydrophobic foam maintains its physical form through wet and dry cycles.\u003c\/p\u003e\n\u003cp\u003eThe system consists of Ultra base resin and MG Accelerator “B”. The accelerator allows an experienced installer to adjust the reaction profile according to job-site temperature and the amount of moisture encountered.\u003c\/p\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e650 cps viscosity:\u003c\/strong\u003e Moderate-viscosity base resin that pumps as a single component after the accelerator has been added.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e300% elongation:\u003c\/strong\u003e Supports use in leaking cracks and joints where some movement is possible.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExpands up to 25 times:\u003c\/strong\u003e The reacting polyurethane foam can expand up to 25 times its initial volume.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e224 kg\/m³ cured density:\u003c\/strong\u003e Measured in accordance with ASTM D-1622.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e300 psi tensile strength:\u003c\/strong\u003e Measured in accordance with ASTM D-638.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eAdjusting the reaction time\u003c\/h3\u003e\n\u003cp\u003eAt 25°C, adding MG Accelerator “B” at 1.25%—equivalent to 1\/2 pint per five gallons—produces an expansion start time of about 50 seconds and completion in about five minutes after contact with water.\u003c\/p\u003e\n\u003cp\u003eAt 25°C, adding MG Accelerator “B” at 2.5%—equivalent to one pint per five gallons—produces an expansion start time of about 30 seconds and completion in about three minutes after contact with water.\u003c\/p\u003e\n\u003ch3\u003eJob-site conditions\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eThe reaction profile is affected by temperature and the amount of moisture encountered.\u003c\/li\u003e\n\u003cli\u003eMG Accelerator “B” is intended to be used by an experienced installer to adjust the reaction profile before pumping.\u003c\/li\u003e\n\u003cli\u003eThe stated reaction times were determined at 25°C.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Green Mountain International","offers":[{"title":"4 Kg","offer_id":48702030250176,"sku":"INJULTRAAERA\/4","price":187.62,"currency_code":"AUD","in_stock":true},{"title":"20 Kg","offer_id":48702030282944,"sku":"INJULTRAAERA\/20","price":582.4,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/moutaingroutultra.png?v=1785472179"}],"url":"https:\/\/adheseal.com.au\/collections\/concrete-civil-products.oembed","provider":"Adheseal","version":"1.0","type":"link"}