{"title":"Protective and Trafficable Finishes","description":"\u003cp\u003eProtective and Trafficable Finishes products for civil construction work. Choose by substrate, exposure, movement, loading and the approved system.\u003c\/p\u003e\u003cp\u003eCheck the product technical data before use.\u003c\/p\u003e","products":[{"product_id":"megapoxy-132","title":"Megapoxy 132","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor floor protection in food and beverage production facilities, pharmaceutical industries, hospital kitchens, and high-traffic forklift ramps, Megapoxy 132 provides a high-strength, solvent-free epoxy barrier. This low-viscosity system is formulated to resist regular industrial cleaning and abrasion, and it carries AS 4020:2018 approval for contact with potable water.\u003c\/p\u003e\n\n \u003ch3\u003eClean environment compliance\u003c\/h3\u003e\n \u003cp\u003eMegapoxy 132 is free from any suspected or potential carcinogens or mutagens, ensuring it will not taint foodstuffs. It conforms to the Department of Primary Industries requirements for coatings and floorings used in export-registered food processing establishments, such as abattoirs. With a low volatile organic compound content of 7 g\/l, it is suitable for application in enclosed commercial spaces including bakeries, cafes, and bathrooms.\u003c\/p\u003e\n\n \u003ch3\u003eApplication and modification\u003c\/h3\u003e\n \u003cp\u003eThe low-viscosity liquid has a mixed viscosity of 620cps at 25°C, allowing application by brush, roller, squeegee, or airless spray. To meet specific slip-resistance and thickness requirements, the system can be modified on-site:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003eIt accepts fine aggregates broadcast between coats to produce a non-slip surface for wet areas and vehicle driveways.\u003c\/li\u003e\n \u003cli\u003eIt can be mixed with fine aggregates to produce high-strength screed floors.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e120MPa ultimate compressive strength (ASTM C579):\u003c\/strong\u003e High load-bearing capacity to withstand heavy forklift traffic and machinery loads without crushing.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e\u0026gt;3MPa concrete bond strength (ASTM D4541):\u003c\/strong\u003e Strong adhesion to prepared concrete, ensuring the coating does not delaminate under shear forces.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e30-minute work time (at 25°C):\u003c\/strong\u003e The application window to spread, level, or broadcast aggregate before the mixed epoxy begins to set.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e24-hour minimum cure (at 25°C):\u003c\/strong\u003e The drying window before the floor can be put back into service, dropping to 12 hours at 35°C and extending to 48 hours at 15°C.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e0.000 gram\/hr m² water vapour transmission (ASTM E96\/E96M):\u003c\/strong\u003e Complete resistance to water vapour passage, protecting the underlying substrate.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eMixing precision:\u003c\/strong\u003e Strict adherence to the 2:1 by volume mixing ratio is required. Inaccuracies or incomplete mixing will lower physical properties, prevent satisfactory curing, or cause discolouration with age.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eMinimum application temperature:\u003c\/strong\u003e Do not apply when substrate or ambient temperatures are below 10°C.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eCoated surfaces:\u003c\/strong\u003e All existing coatings must be removed prior to application. Bonding directly to existing paint or coatings reduces bond strength compared to a freshly prepared substrate.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eMetal preparation limits:\u003c\/strong\u003e Wire brushing is not satisfactory for metal substrates and provides minimal adhesion. Metals must be grit blasted or mechanically abraded to bright metal.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eSurface preparation\u003c\/h3\u003e\n \u003cp\u003eFor successful adhesion, substrates must be prepared according to their material class:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eConcrete:\u003c\/strong\u003e Must be free from grease and oil. Remove surface laitance by scabbling, grit blasting, or grinding. If mechanical prep is not possible, acid etch with a 1:1 hydrochloric acid and water mix at 0.5 litres per square metre, react for 10 minutes, scrub, rinse, and allow to dry for 24 hours until surface dry.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eMetal surfaces:\u003c\/strong\u003e Grit blast to AS 1627.2.2002, or mechanically abrade to a clean, bright finish. Degrease immediately after abrasion by flooding with an industrial grade degreaser.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eCoated concrete:\u003c\/strong\u003e Flame-clean or use a scutching tool to remove paint, then complete preparation with diamond grinding or scabbling.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eCoated metals:\u003c\/strong\u003e Strip paint or galvanising using a high-quality paint stripper, followed by grit blasting or grinding to a bright metal finish.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eClean-up\u003c\/h3\u003e\n \u003cp\u003eTo keep mixing implements, squeegees, and application tools clean before the epoxy cures, use \u003ca href=\"\/products\/megapoxy-thinners\"\u003eMegapoxy Thinners\u003c\/a\u003e. Wear disposable rubber gloves during application and clean-up to maintain proper industrial hygiene.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Megapoxy","offers":[{"title":"Grey \/ 30L Kit","offer_id":37551473983680,"sku":"MP132GR\/30","price":909.36,"currency_code":"AUD","in_stock":true},{"title":"Clear \/ 30L Kit","offer_id":37551474049216,"sku":"MP132CL\/30","price":849.73,"currency_code":"AUD","in_stock":true},{"title":"Clear \/ 15L Kit","offer_id":37551474081984,"sku":"MP132CL\/15","price":506.86,"currency_code":"AUD","in_stock":true},{"title":"Clear \/ 4.5L Kit","offer_id":45248070156480,"sku":"MP132CL\/4.5","price":195.36,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/megapoxy-132-high-strength-epoxy-as4020-floors-adheseal.png?v=1763706786"},{"product_id":"megapoxy-mc","title":"Megapoxy MC","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eFor high-traffic food and beverage facilities, chemical bunds, and wastewater infrastructure, Megapoxy MC provides a 100% solids, VOC-free epoxy maintenance coating that resists heavy abrasion, chemical exposure, and hydrogen sulphide gas. It protects concrete and steel substrates, curing to a hygienic, dust-free gloss finish that is suitable for structures in contact with foodstuffs.\u003c\/p\u003e\n\u003ch3\u003eChemical and wear protection\u003c\/h3\u003e\n\u003cp\u003eMegapoxy MC is a high-build protective coating formulated to seal floors, walls, and structural steel against aggressive environmental hazards. For harsh or highly aggressive service conditions, a three-coat application is recommended to achieve a total cured dry film thickness of 0.4 mm to 0.5 mm. The cured coating resists chemical splash and immersion, protecting containment areas, plant rooms, and factory floors from chemical degradation. Where slip resistance is required for ramps, car parks, or forklift areas, the freshly applied first coat accepts a broadcast of epoxy-quality sand, glass beads, carborundum, or silicone oxide, or a fine aggregate can be mixed directly into the coating at a rate of 250 grams per 5 kg kit.\u003c\/p\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompressive strength (ASTM D695):\u003c\/strong\u003e 70 MPa (MC2 Rapid version only), providing a high-strength surface that withstands forklift traffic and heavy mechanical loads.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBond strength to concrete (ASTM D4541):\u003c\/strong\u003e \u0026gt;3 MPa, ensuring the coating adheres to prepared concrete substrates without delaminating under shear stress.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTensile bond strength to steel (ASTM D897):\u003c\/strong\u003e 13 MPa, providing high adhesion to properly prepared bright metal surfaces.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWork time (at 25°C):\u003c\/strong\u003e 2 hours for the Standard version or 30 minutes for the MC2 Rapid version, defining the application window after mixing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRe-coat window (at 25°C):\u003c\/strong\u003e 8 hours for Standard or 4 hours for MC2 Rapid. If more than 24 hours elapses between coats, you must abrade the surface to a uniform dull finish using 60-grit paper.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoverage:\u003c\/strong\u003e 20 m² to 25 m² per 5 kg kit, or 80 m² to 100 m² per 20 kg kit.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eLimitations\u003c\/h3\u003e\n\u003cp\u003eDo not apply Megapoxy MC if the substrate temperature is below 10°C. Do not rely on wire brushing for metal preparation, as it is not entirely satisfactory and yields minimal adhesion only. Do not apply directly to existing coatings; bonding to coated surfaces will result in inferior bond strengths compared to bare, prepared substrates. Mixing ratios must be precise; inaccuracies or incomplete mixing will lower the physical properties of the cured system, and may prevent a complete cure or cause discolouration over time.\u003c\/p\u003e\n\u003ch3\u003eSubstrate preparation\u003c\/h3\u003e\n\u003cp\u003eTo ensure high adhesion, substrates must be prepared according to their material class:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eConcrete:\u003c\/strong\u003e Must be free from grease and oil. Remove surface laitance by mechanical abrasion (scabbling, grit blasting, or grinding). If mechanical preparation is not possible, acid etch using a 1:1 hydrochloric acid and water mix at 0.5 litres per square metre, allow to react for 10 minutes, scrub with a stiff broom, wash thoroughly, and allow to dry for 24 hours. Concrete must be surface dry.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMetal surfaces:\u003c\/strong\u003e Grit blast to AS CK 9.4 - 1964 Class 3 finish. If grit blasting is not possible, mechanically abrade to clean, bright metal, then degrease by flooding the surface with an industrial grade degreaser.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoated concrete:\u003c\/strong\u003e Remove all traces of existing paint by flame-cleaning or using a scutching tool, followed by diamond grinding or scabbling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoated metals:\u003c\/strong\u003e Remove all paint, galvanising, or zinc coatings using a high-quality paint stripper, followed by grit blasting or grinding to a bright metal finish.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMixing and application\u003c\/h3\u003e\n\u003cp\u003eMegapoxy MC is supplied in pre-metered kits. Pour the entire contents of Part B into the Part A container. Mix the components thoroughly, scraping the base and corners of the tin, then scrape the sides and mix again. Use a timer and mix to the following durations:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMegapoxy MC (Standard):\u003c\/strong\u003e Mix for a minimum of 3 minutes, scrape the sides, and mix for a further 2 minutes.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMegapoxy MC2 (Rapid):\u003c\/strong\u003e Mix for a minimum of 2 minutes, scrape the sides, and mix for a further 1 minute.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eOn highly porous concrete surfaces, prime first using \u003ca href=\"\/products\/megapoxy-lvs\"\u003eMegapoxy LVS\u003c\/a\u003e (Low Viscosity Sealer) applied at 8 m² to 10 m² per litre, and overcoat within 8 to 24 hours. Megapoxy MC can be thinned up to 10% with \u003ca href=\"\/products\/megapoxy-thinners\"\u003eMegapoxy Thinners\u003c\/a\u003e on the first coat, and 5% on the second coat, to improve workability. All thinners must evaporate before applying the next coat. Use Megapoxy Thinners to clean tools and mixing equipment immediately after use.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Megapoxy","offers":[{"title":"Caribbean Blue \/ 5kg Kit","offer_id":45534512480448,"sku":"MPMCCAR\/5","price":173.63,"currency_code":"AUD","in_stock":true},{"title":"Caribbean Blue \/ 20kg Kit (Made to Order: MOQ 16 Kits)","offer_id":45534542954688,"sku":"MPMCCAR\/20","price":601.79,"currency_code":"AUD","in_stock":true},{"title":"Blue \/ 5kg Kit","offer_id":45534512513216,"sku":"MPMCBLU\/5","price":173.63,"currency_code":"AUD","in_stock":true},{"title":"Blue \/ 20kg Kit (Made to Order: MOQ 16 Kits)","offer_id":45534562025664,"sku":"MPMCBLU\/20","price":514.69,"currency_code":"AUD","in_stock":true},{"title":"Pacific Blue \/ 5kg Kit","offer_id":37551474344128,"sku":"MPMCPB\/5","price":173.63,"currency_code":"AUD","in_stock":true},{"title":"Pacific Blue \/ 20kg Kit","offer_id":45534533157056,"sku":"MPMCPB\/20","price":601.79,"currency_code":"AUD","in_stock":true},{"title":"Charcoal \/ 5kg Kit","offer_id":38161263591616,"sku":"MPMCCHAR\/5","price":173.63,"currency_code":"AUD","in_stock":true},{"title":"Charcoal \/ 20kg Kit (Made to Order: MOQ 16 Kits)","offer_id":44064672940224,"sku":"MPMCCAR\/20","price":601.79,"currency_code":"AUD","in_stock":true},{"title":"Dark Grey \/ 5kg Kit","offer_id":37551474213056,"sku":"MPMCDKGR\/5","price":173.63,"currency_code":"AUD","in_stock":true},{"title":"Dark Grey \/ 20kg Kit (Made to Order: MOQ 16 Kits)","offer_id":44064672743616,"sku":"MPMCDKGR\/20","price":641.9,"currency_code":"AUD","in_stock":true},{"title":"Mid Grey \/ 5kg Kit","offer_id":45534512545984,"sku":"MPMCMIDGR\/5","price":173.63,"currency_code":"AUD","in_stock":true},{"title":"Mid Grey \/ 20kg Kit (Made to Order: MOQ 16 Kits)","offer_id":45534512578752,"sku":"MPMCMIDGR\/20","price":641.9,"currency_code":"AUD","in_stock":true},{"title":"Grey \/ 5kg Kit","offer_id":37551474245824,"sku":"MPMCGR\/5","price":173.63,"currency_code":"AUD","in_stock":true},{"title":"Grey \/ 20kg Kit (Made to Order: MOQ 16 Kits)","offer_id":44064672776384,"sku":"MPMCGR\/20","price":641.9,"currency_code":"AUD","in_stock":true},{"title":"Koala Grey \/ 5kg Kit","offer_id":37551474278592,"sku":"MPMCKOGR\/5","price":173.63,"currency_code":"AUD","in_stock":true},{"title":"Koala Grey \/ 20kg Kit (Made to Order: MOQ 16 Kits)","offer_id":45534562943168,"sku":"MPMCKGK\/20","price":601.79,"currency_code":"AUD","in_stock":true},{"title":"Safety Yellow \/ 5kg Kit","offer_id":37551474376896,"sku":"MPMCYEL\/5","price":206.86,"currency_code":"AUD","in_stock":true},{"title":"Safety Yellow \/ 20kg Kit (Made to Order: MOQ 16 Kits)","offer_id":45534562975936,"sku":"MPMCYEL\/20","price":549.0,"currency_code":"AUD","in_stock":true},{"title":"White \/ 5kg Kit","offer_id":37551474311360,"sku":"MPMCWH\/5","price":173.63,"currency_code":"AUD","in_stock":true},{"title":"White \/ 20kg Kit (Made to Order: MOQ 16 Kits)","offer_id":45534561894592,"sku":"MPMCWH\/20","price":601.79,"currency_code":"AUD","in_stock":true},{"title":"Black \/ 5kg Kit","offer_id":37551474180288,"sku":"MPMCBLK\/5","price":173.63,"currency_code":"AUD","in_stock":true},{"title":"Black \/ 20kg Kit (Made to Order: MOQ 16 Kits)","offer_id":45534545117376,"sku":"MPMCBLK\/20","price":601.79,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/megapoxy-mc-chemical-resistant-tank-linings-adheseal.png?v=1763706786"},{"product_id":"megapoxy-lvs","title":"Megapoxy LVS","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor internal sealing of concrete tanks, waterproofing walls and floors, and toughening timber surfaces, Megapoxy LVS is a two-component, clear liquid epoxy formulated to penetrate porous substrates. With a low mixed viscosity of 90cps, it sinks into the pores of concrete, timber, bricks, mortar, and natural stone to seal, harden, and waterproof from within.\u003c\/p\u003e\n\n \u003ch3\u003eHow it works\u003c\/h3\u003e\n \u003cp\u003eMegapoxy LVS functions by capillary action, penetrating deep into the substrate before curing. Once cured, it creates a high-strength barrier with a compressive strength of 80Mpa and a concrete bond strength exceeding 3Mpa, making the treated surface mechanically stronger than the concrete itself. It seals internal masonry walls, consolidates soft or porous brickwork, and hardens timber surfaces against wear. It also serves as the compatible primer coat for Megapoxy floor coatings, establishing a secure structural bond to the dry substrate.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003e90cps mixed viscosity:\u003c\/strong\u003e A thin liquid that easily penetrates fine pores and capillaries in dense substrates at 25°C.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e80Mpa compressive strength (ASTM D695):\u003c\/strong\u003e Delivers a cured matrix that reinforces weak concrete and masonry under heavy mechanical loads.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e30-minute work time (at 25°C):\u003c\/strong\u003e The working window to mix, apply, and back-roll the sealer before the chemical cure begins to thicken the liquid.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e24-hour full cure (at 25°C):\u003c\/strong\u003e Reaches structural service strength within 24 hours at standard temperature, dropping to 12 hours at 35°C, and extending to 48 hours at 15°C.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e4-hour thin film cure (at 25°C):\u003c\/strong\u003e Cures quickly when applied as a thin sealer coat, reducing the window before subsequent coatings can be considered.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eConcrete tanks:\u003c\/strong\u003e Internal sealing to prevent water egress or chemical penetration.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eWalls and floors:\u003c\/strong\u003e Deep-penetrating waterproofing barrier for porous masonry structures.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eBricks and mortar:\u003c\/strong\u003e Internal sealing to consolidate old, crumbly, or dusting brick joints.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eConcrete floors:\u003c\/strong\u003e Hardening and dust-proofing porous concrete floors, or priming prior to applying Megapoxy floor coatings.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eStructural concrete:\u003c\/strong\u003e Protection against environmental ingress and carbonation.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eTimber surfaces:\u003c\/strong\u003e Toughening and consolidating soft, dry, or worn timber structures.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eMust be applied to thoroughly dry substrates only; moisture will compromise adhesion.\u003c\/li\u003e\n \u003cli\u003eDo not apply at temperatures below 10°C.\u003c\/li\u003e\n \u003cli\u003eMust be applied as thinly as possible and not allowed to pool. If pooling occurs, excess material must be wiped up immediately to leave a thin surface film.\u003c\/li\u003e\n \u003cli\u003eBonding to existing painted or coated surfaces will result in inferior bond strength compared to a freshly prepared substrate. All previous coatings must be removed.\u003c\/li\u003e\n \u003cli\u003eWire brushing of metal surfaces is not satisfactory and provides minimal adhesion only.\u003c\/li\u003e\n \u003cli\u003eInaccuracies in the 2:1 mixing ratio or poor hand mixing will lower the physical properties of the system, prevent a satisfactory cure, and cause discolouration with age.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eSurface preparation\u003c\/h3\u003e\n \u003cp\u003e\u003cstrong\u003eConcrete:\u003c\/strong\u003e Must be free from grease and oil. Remove surface laitance by scabbling, grit blasting, or grinding. If mechanical preparation is impossible, acid etch using a 1:1 mix of hydrochloric acid and water at a rate of 0.5 litres per square metre. Allow to react for 10 minutes, wash thoroughly, scrub with a stiff broom, and allow to dry for a minimum of 24 hours.\u003c\/p\u003e\n \u003cp\u003e\u003cstrong\u003eMetal surfaces:\u003c\/strong\u003e Grit blast to AS CK 9.4 - 1964 Class 3 finish, or mechanically abrade to a clean, bright metal surface, then flood with an industrial grade degreaser.\u003c\/p\u003e\n \u003cp\u003e\u003cstrong\u003eTimber:\u003c\/strong\u003e Remove all damaged, loose, or rotted timber back to a clean, dust-free surface.\u003c\/p\u003e\n \u003cp\u003e\u003cstrong\u003eCoated surfaces:\u003c\/strong\u003e Remove paint from concrete using flame-cleaning or a scutching tool, followed by diamond grinding or scabbling. Remove paint and galvanizing from metal using a high-quality paint stripper followed by grit blasting or grinding.\u003c\/p\u003e\n\n \u003ch3\u003eApplication guide\u003c\/h3\u003e\n \u003cp\u003eThoroughly mix Part A and Part B at a ratio of 2 Parts A to 1 Part B by volume. Apply using a brush or roller.\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003ePriming:\u003c\/strong\u003e Apply a minimum of 1 coat prior to overcoating with Megapoxy floor coating products.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eCoating, sealing, or hardening:\u003c\/strong\u003e Apply a minimum of 2 coats.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eTraffic window:\u003c\/strong\u003e Allow the system to cure for 18 to 24 hours before opening the treated area to traffic.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eCleanup:\u003c\/strong\u003e Clean mixing implements and application tools immediately after use with \u003ca href=\"\/products\/megapoxy-thinners\"\u003eMegapoxy Thinners\u003c\/a\u003e.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eCoverage\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eConcrete (Wood Float Finish):\u003c\/strong\u003e 75m² per 15-litre kit.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eConcrete (Steel Float Finish):\u003c\/strong\u003e 150m² per 15-litre kit.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eBricks:\u003c\/strong\u003e 75m² per 15-litre kit.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eTimber:\u003c\/strong\u003e 75m² per 15-litre kit.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"Megapoxy","offers":[{"title":"6L Kit","offer_id":46003517259968,"sku":"MPLVS\/6","price":216.72,"currency_code":"AUD","in_stock":true},{"title":"15L Kit","offer_id":46003517292736,"sku":"MPLVS\/15","price":500.26,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/megapoxy-lvs-low-viscosity-epoxy-waterproofing-adheseal.png?v=1763706888"},{"product_id":"gripset-ls-external-trafficable-coating","title":"Gripset LS Trafficable Coating","description":"\u003cdiv role=\"main\"\u003e\n\u003cp\u003eFor external rooftops, decks, balconies, and walkways where a slip-resistant, weather-exposed finish is required, Gripset LS Trafficable Coating provides a hard-wearing top coat that withstands light foot traffic and permanent UV exposure. This solvent-free, non-shrinking formulation applies over suitable base liquid membranes to protect the underlying waterproofing system from climatic wear without requiring sand casting or aggregate additions.\u003c\/p\u003e\n\u003ch3\u003eWhat it does\u003c\/h3\u003e\n\u003cp\u003eGripset LS Trafficable Coating acts as a protective, light grey, non-slip finish coat over base liquid membranes on substrates such as concrete, screeds, compressed fibre cement sheeting, exterior grade plywood, and well-bonded existing tiles or pavers. It is flexible to accommodate thermal movement, though it is non-elastomeric and must not be used as a standalone crack-bridging membrane on suspended areas. It resists algae and fungi growth, prevents water ponding degradation, and can be built up in high-film thicknesses to increase long-term durability on exposed service areas and maintenance walkways.\u003c\/p\u003e\n\u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e108 Shore A hardness (ASTM D2240-97):\u003c\/strong\u003e A dense, high-durability surface profile that resists physical wear from light maintenance foot traffic.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e45% Elongation (AS1145.3):\u003c\/strong\u003e Provides controlled flexibility to move with structural substrates without cracking, while remaining non-elastomeric.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1.0mm minimum Dry Film Thickness (DFT):\u003c\/strong\u003e Achieved by applying two separate coats at 750 microns wet film thickness (WFT) per coat, ensuring uniform coverage of 1.5 litres\/m² across the system. An optional third coat can be applied to reach 1.5mm DFT for extended service life.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e4-hour recoat window:\u003c\/strong\u003e Allows multi-coat build-up within a single day under standard conditions (23°C and 50% relative humidity) before traffic or flood testing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e10-day full cure:\u003c\/strong\u003e The required curing window before the system can be flood tested or subjected to its full design service conditions.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhere to use it\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRooftops:\u003c\/strong\u003e Applied as the UV-stable protective top coat over \u003ca href=\"\/products\/gripset-38fc\"\u003eGripset 38FC\u003c\/a\u003e, Gripset P39, or Xpress Multi Pro base membranes.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDecks and balconies:\u003c\/strong\u003e Protects primary elastomeric membrane systems from localized wear and weathering.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExposed rooftop plant and maintenance areas:\u003c\/strong\u003e Provides a dedicated, non-slip service path for maintenance personnel around machinery.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWalkways:\u003c\/strong\u003e Serves as a standalone water-resistant, slip-resistant coating over ground-level paths, or as part of a multi-layer membrane system on suspended walkways.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eLimitations\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDo not use as a standalone, elastomeric crack-bridging membrane for suspended areas. Suspended areas require a primary base layer of Gripset P-39 or Xpress Multi Pro.\u003c\/li\u003e\n\u003cli\u003eNot suitable for areas subject to vehicular traffic or heavy commercial foot traffic.\u003c\/li\u003e\n\u003cli\u003eDo not apply in areas subject to rising damp or negative hydrostatic pressure.\u003c\/li\u003e\n\u003cli\u003eDo not apply when the surface temperature is below 5°C or above 35°C, or if rain is imminent.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHow to apply\u003c\/h3\u003e\n\u003cp\u003eAll substrates must be clean, dry, and free from surface contaminants such as curing compounds, laitance, or existing failed coatings. Concrete must cure for a minimum of 28 days, and screeds or sand-cement renders for 7 days. Apply the product by brush or medium nap roller. Apply the first coat at 750 microns wet film thickness (10m² coverage per 15-litre pail) and allow to dry for 4 hours. Apply the second coat at right angles to the first coat to ensure complete, pinhole-free coverage. Use a wet film gauge during application to verify and regulate consistent film build across the entire surface area. Clean up tools and spills with water while the coating is wet; dried material must be removed mechanically.\u003c\/p\u003e\n\u003c\/div\u003e","brand":"Gripset","offers":[{"title":"Default Title","offer_id":37552212148416,"sku":"GRIPLSGREY\/15","price":230.09,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/gripset-ls-15l-non-slip-waterproofing-membrane-adheseal.png?v=1763709353"},{"product_id":"silcor-top-coat-80","title":"Silcor Top Coat 80 Waterproof Membrane","description":"\u003cdiv role=\"main\"\u003e\n \u003cp\u003eFor exposed external areas where an underlying waterproofing membrane requires protection from sun and foot traffic, Silcor Top Coat 80 Waterproof Membrane provides a tough, colour-fast, aliphatic polyurethane finish. It is formulated to protect SILCOR 580, SILCOR 780 HI-LP, SILCOR 790 HI (CHEMSPRAY 790), and SILCOR 990 MP (A) (CHEMSPRAY 690) membrane systems in high-exposure zones including balconies, decks, plant room roofs, and lift motor room roofs.\u003c\/p\u003e\n\n \u003ch3\u003eUV protection and foot-traffic durability\u003c\/h3\u003e\n \u003cp\u003eSilcor Top Coat 80 Waterproof Membrane seals exposed external waterproofing systems against UV degradation and physical wear. The aliphatic polyurethane chemistry ensures long-term colour-fast performance on highly visible details such as perimeter turn-ups, penetrations, and window or sill flashings. Once applied, the coating develops immediate resistance to rain damage, preventing wash-offs on unstable weather days. It cures to a permanently flexible, non-slip finish with high adhesion to the underlying SILCOR membrane, maintaining system integrity under foot traffic without cracking or peeling.\u003c\/p\u003e\n\n \u003ch3\u003eNumbers that matter\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eDrying time of 2 hours (at 25ºC):\u003c\/strong\u003e Allows rapid trade access to the deck or roof area after application.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eShore Hardness of 75-80°A:\u003c\/strong\u003e Delivers a tough, trafficable barrier that resists mechanical scuffing and puncture.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eMinimum coverage of 0.3 kg\/m²:\u003c\/strong\u003e Achieves the minimum required dry film thickness (DFT) of 0.15mm to ensure reliable UV and wear protection.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003e5:1 mix ratio by weight:\u003c\/strong\u003e High-precision resin-to-hardener proportioning required to ensure complete cross-linking and full cure properties.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eTensile strength of 2 MPa (AS1145):\u003c\/strong\u003e Provides the mechanical strength necessary to withstand movement across joints and flashing details.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eWhere to use it\u003c\/h3\u003e\n \u003cp\u003eThis protective coating is suitable for all grades of SILCOR waterproof membranes used in exposed external situations, specifically:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003ePlant room and lift motor room roofs\u003c\/li\u003e\n \u003cli\u003eBalconies and recreation decks\u003c\/li\u003e\n \u003cli\u003ePerimeter turn-ups and structural penetrations\u003c\/li\u003e\n \u003cli\u003eSill or window flashings\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eApplication and mixing sequence\u003c\/h3\u003e\n \u003cp\u003eTo ensure proper curing and performance, installers must follow the specific mixing and application steps:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003e\n\u003cstrong\u003eSubstrate preparation:\u003c\/strong\u003e The surface of the SILCOR membrane must be completely clean and dry before applying the top coat.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eMixing:\u003c\/strong\u003e Stir the resin and hardener components separately with a clean blade. Combine them in a clean, dry container at the 5:1 weight ratio and mix thoroughly using a high-speed dissolver for 5 minutes prior to application.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eManual application:\u003c\/strong\u003e Apply in two coats using a brush or roller. Work the second coat in a cross direction to the first coat to ensure a uniform, pinhole-free finish.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eSpray application:\u003c\/strong\u003e Apply in a single, continuous wet-on-wet spray pass.\u003c\/li\u003e\n \u003cli\u003e\n\u003cstrong\u003eClean-up:\u003c\/strong\u003e Clean wet tools and equipment with MULTITEK \u003ca href=\"\/products\/xylene\"\u003eXylene\u003c\/a\u003e or \u003ca href=\"\/products\/methylated-spirits\"\u003emethylated spirits\u003c\/a\u003e before the coating cures.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n \u003ch3\u003eLimitations\u003c\/h3\u003e\n \u003cul\u003e\n \u003cli\u003eDo not attempt to reuse mixed product once it has become thick and stringy; discard it immediately.\u003c\/li\u003e\n \u003cli\u003eDo NOT add solvent to the mix under any circumstances.\u003c\/li\u003e\n \u003cli\u003eOnce opened, sealed pails may solidify within a few days due to atmospheric moisture exposure.\u003c\/li\u003e\n \u003cli\u003eDo not store unmixed product where it is exposed to weather and direct sun; keep in a cool, dry, protected area.\u003c\/li\u003e\n \u003c\/ul\u003e\n\u003c\/div\u003e","brand":"GCP","offers":[{"title":"Light Grey","offer_id":48532863058112,"sku":"SILCORTC80LGR\/18","price":691.21,"currency_code":"AUD","in_stock":true},{"title":"White","offer_id":48532863090880,"sku":"SILCORTC80WH\/18","price":691.22,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0507\/3630\/0224\/files\/topcoat80.png?v=1782958757"}],"url":"https:\/\/adheseal.com.au\/collections\/civil-construction-protect.oembed","provider":"Adheseal","version":"1.0","type":"link"}